以下為個人的一些小小經驗
都是在本版夙夜匪懈參考來的
其中要感謝各位版主及先進的指教
若有錯誤請各位大大多多指教
(menu的12 15 功能不是很了解
請問各為哪有詳細的說明文章)
----------------------------------------------------------------------
我是用rs232連接atu-r 和com2
再執行"C:\Program Files\Accessories\HyperTerminal\HYPERTRM.EXE"
會叫你輸入一名稱 隨便
選擇連接埠<--com2
設定速率(剛開始為r51af1為9600 更新為aj3後為115200)
鮑率設錯畫面會亂掉
此時將power off 在power on
press any key 進入debug mode
鍵入atur
點選HYPERTRM之轉送-傳送檔案
(要選xmoden 為V2.50AJ3之.bin)<------此乃韌體
會自動reboot
再次進入debug mode
鍵入atur3
點選HYPERTRM之轉送-傳送檔案
(要選xmoden 為V2.50AJ3之.rom)<------此乃內部設定
鍵入atgo
reboot
press any key
輸入密碼 1234
來到主畫面
之後為我的設定
----------------------------------------------------
(...)<---為改成軟體撥接
-----------------------------------------------------------------------------
Copyright (c) 1994 - 2000 ZyXEL Communications Corp.
Prestige 642 Main Menu
Getting Started Advanced Management
1. General Setup 21. Filter Set Configuration
3. Ethernet Setup 22. SNMP Configuration
4. Internet Access Setup 23. System Password
24. System Maintenance
25. IP Routing Policy Setup
Advanced Applications 26. Schedule Setup
11. Remote Node Setup
12. Static Routing Setup
15. SUA Server Setup 99. Exit
--------------------------------------------------------------------------
Menu 1 - General Setup
System Name= HiNet
Location=
Contact Person's Name=
Route IP= Yes<---(用軟體時也可yes)
Route IPX= No
Bridge= No<----一定要no (若要用軟體撥接改yes)
---------------------------------------------------------------------
Menu 3.2 - TCP/IP and DHCP Ethernet Setup
DHCP Setup<----可不設
DHCP= Server
Client IP Pool Starting Address= 192.168.1.2
Size of Client IP Pool= 253
Primary DNS Server= 168.95.1.1
Secondary DNS Server= 168.95.192.1
Remote DHCP Server= N/A
TCP/IP Setup:<----不動
IP Address= 192.168.1.1
IP Subnet Mask= 255.255.255.0
RIP Direction= Both
Version= RIP-2B
Multicast= IGMP-v2
IP Policies=
Edit IP Alias= No
---------------------------------------------------------------------
Menu 4 - Internet Access Setup
ISP's Name= HiNet
Encapsulation= PPPoE<----(FRC 1483)
Multiplexing= LLC-based
VPI #= 0
VCI #= 33<--hinet
Service Name= ANY<---一定要ANY 不可用別的
My Login= [email protected](hinet為[email protected]不可只用id)
My Password=
Single User Account= Yes
IP Address Assignment= Dynamic<----都可以
IP Address= N/A
ENET ENCAP Gateway= N/A
-----------------------------------------------------------------------
Menu 11.1 - Remote Node Profile
(這個會隨著menu4改變)
Rem Node Name= HiNet Route= IP<--要和menu1一樣
Active= Yes Bridge= No<--要記得改no(軟體要改yes)
Encapsulation= PPPoE Edit PPP Options= No
Multiplexing= LLC-based Rem IP Addr= 0.0.0.0
Incoming: Edit IP/IPX/Bridge= No
Rem Login=
Rem Password=
Outgoing: Session Options:
My Login= Edit Filter Sets= No
My Password= PPPoE Idle Timeout(sec)= 0
Authen= CHAP/PAP PPPoE Service Name= ANY
Schedule Sets= 1
-------------------------------------------------------------------------
Menu 24.2.1 - System Maintenance - Information
Name: HiNet
Routing: IP
ZyNOS S/W Version: V2.50(AJ.3)Feb_2 | 2/2/2001
ADSL Chipset Vendor: Alcatel, Version 3.7.12
Standard: ANSI T1.413
LAN
Ethernet Address: 00:a0:c5:16:95:18
IP Address: 192.168.1.1
IP Mask: 255.255.255.0
DHCP: Server
----------------------------------------------------------------------
Menu 24.1 - System Maintenance - Status
e-Lnk Status TxPkts RxPkts Errors Tx B/s Rx B/s Up Time
PPPoE Up<-- 98259 117893 0 0 0 0:11:40
(若成功你會看到up 此時你可用ping http://www.hinet.net試試)
Ethernet: WAN:
Status: 10M/Half Duplex Tx Pkts: 115281 Line Status: Up
Collisions: 0 Rx Pkts: 94945 Upstream Speed: 64 kbps
CPU Load = 2.63% Downstream Speed: 512 kbps
Press Command:
COMMANDS: 1-Reset Counters ESC-Exit
----------------------------------------------------------------------------------
Menu 24.4 - System Maintenance - Diagnostic
ADSL System
1. Reset ADSL 21. Reboot System<--
(可不用拔電源就進入debug mode)
22. Command Mode
TCP/IP
12. Ping Host
Enter Menu Selection Number:
-----------------------------------------------------------------------
Menu 24 - System Maintenance
1. System Status
2. System Information and Console Port Speed
3. Log and Trace
4. Diagnostic
5. Backup Configuration
6. Restore Configuration
7. Upload Firmware
(5.6.7.選擇後可備分還原更新你的.bin.rom)
(看完說明後選y再HYPERTRM之轉送-傳送/接收檔案)
8. Command Interpreter Mode
10. Time and Date Setting
(時間設定 有一次我設錯後整個畫面都沒了
只好重新restore .rom了
不過我的畫面有點怪怪了 都沒有照正確的格子)
Enter Menu Selection Number:
------------------------------------------------------------
 |
回覆時引用此文章
書籤