遠傳家用電話節費盒WT-5 (WTLP201)

第 1 頁,共 10 頁 1 2 3 ... 末頁末頁
顯示結果從第 1 筆 到 10 筆,共計 92 筆
  1. #1
    會員
    註冊日期
    2001-04-19
    討論區文章
    161

    遠傳家用電話節費盒WT-5 (WTLP201)

    剛收到了WT-5
    小巧到不行,雖然不是ZyXEL代工了不過用料似乎還不錯
    91%鋁質電容!!真是嚇死人~

    主處理器單一一顆Realtek RTL8972B,大部分用在IP Phone中
    不過如果要用NAT + Wifi可能就不太夠力
    而且沒有散熱片,改天去買一片加上去

    中規中矩的8MB SPI Flash,可惜沒有什麼第三方韌體也沒有Opensource.

    超大容量64MB Memory當SIP ATA絕對足夠

    正面圖

    背面圖


    備用圖
    正面圖

    背面圖


    以上

    2010-02-07
    Console Boot Message 38400,N,8,1
    密碼研究中

    Normal Boot / Software Reset

    Eon SPI (8 MByte)!

    DDR DRAM 64 MB @ 195 MHz

    Soundwin (Wagaly Talk Lite Plus) at 2009.06.17-13:28+0800 version v1.5.3 [16bit](390MHz)

    decompressing kernel:
    Uncompressing Linux... done, booting the kernel.
    done decompressing kernel.
    early printk enabled
    Determined physical RAM map:
    memory: 04000000 @ 00000000 (usable)
    Initial ramdisk at: 0x803eb000 (1892352 bytes)
    On node 0 totalpages: 16384
    zone(0): 16384 pages.
    zone(1): 0 pages.
    zone(2): 0 pages.
    Kernel command line: root=/dev/ram console=0 ramdisk_start=0
    Calibrating delay loop... 389.12 BogoMIPS
    Memory: 55220k/65536k available (3598k kernel code, 10316k reserved, 2286k data, 8k init, 0k highmem)
    Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
    Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
    Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
    Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
    Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
    check_wait... unavailable.
    POSIX conformance testing by UNIFIX
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    Starting kswapd
    Serial driver version 6.02 (2003-03-12) with no serial options enabled
    ttyS00 at 0x2000 (irq = 5) is a rtl_uart1
    state->flags=00000000
    Realtek GPIO Driver for Flash Reload Default
    block: 128 slots per queue, batch=32
    RAMDISK driver initialized: 16 RAM disks of 15000K size 1024 blocksize
    PPP generic driver version 2.4.1
    MPPE/MPPC encryption/compression module registered
    SPI INIT
    flash device: 0x400000 at 0xbfe00000
    probe realtek
    get SPI CS0
    maker:1c type:20 sector_cnt:128
    capacity_id = 23
    get SPI CS1
    maker:0 type:0 sector_cnt:0
    capacity_id = 0

    Eon matched!!get SPI chip driver!
    Physically mapped flash: Found an alies 0x800000 for the chip at 0x0, eon device detect.
    probe ends
    probe realtek2
    Creating 1 MTD partitions on "Physically mapped flash":
    0x00000000-0x00800000 : "Wagaly Talk Lite Plus only"
    RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
    Cannot find driver for DiskOnChip Millennium at 0x6000
    usb.c: registered new driver usbdevfs
    usb.c: registered new driver hub
    rtl8652_ehci : irq 7, b8021000
    usb.c: new USB bus registered, assigned bus number 1
    rtl8652_ehci : USB f.f enabled, EHCI 1.00, driver 2003-Dec-29/2.4
    hub.c: USB hub found
    hub.c: 2 ports detected
    host/usb-ohci-rtl8652.c: USB OHCI at membase 0xb8020000, IRQ 7
    host/usb-ohci-rtl8652.c: usb-
    usb.c: new USB bus registered, assigned bus number 2
    hub.c: USB hub found
    hub.c: 2 ports detected
    RTL8192SU driver version 0.2 (2009-05-20)
    usb.c: registered new driver RTL8192SU
    Realtek 865x Ethernet driver v0.6 (Mar 26, 2008)
    Initialize Hardware Tables Driver ......
    chip name: 8196B, chip revid: 2
    eth0: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:11, IRQ 2
    eth1: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:22, IRQ 2
    Realtek FastPath v1.08
    =============RTK VOIP SUITE=============
    INITIAL VOIP MANAGER PROGRAM
    INITIAL VOIP DSP PROGRAM
    RTK VoIP Version: 1.1.1
    IMEM_init_OK
    INIT VAR OK
    === RTP Event Send Tasklet Initialization ===
    ========================================

    ====== RTK PCM Controller Initialization =======
    -------Si3217x Driver Rev 0.1------
    Start SLIC init....
    ( GPIO E ) for SLIC[0]...=> OK !
    SLIC0 ID: Si32178 Revision B
    Starting calibration... ...
    SLIC0 master state check pass!
    Init OK!
    Start DAA init....
    Init OK!
    Request IRQ for PCM Controller OK!.
    ================= FISISH ===============
    <6>NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP, IGMP
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 4096 bind 8192)
    Linux IP multicast router 0.06 plus PIM-SM
    ip_conntrack version 2.1 (512 buckets, 4096 max) - 324 bytes per conntrack
    PPTP netfilter connection tracking: registered
    PPTP netfilter NAT helper: registered
    ip_tables: (C) 2000-2002 Netfilter core team
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    NET4: Ethernet Bridge 008 for NET4.0
    RAMDISK: LZMA Compressed image found at block 0
    Freeing initrd memory: 1848k freed
    VFS: Mounted root (ext2 filesystem).
    Freeing unused kernel memory: 8k freed
    mount /proc file system ok!
    serial console detected. Disabling virtual terminals.
    init started: BusyBox v1.00-pre8 (2009.08.17-05:45+0000) multi-call binary
    write file: /tmp/private_key OK!
    flash voip check
    Setup BRIDGE interface
    killall: syslogd: no process killed
    killall: klogd: no process killed
    SIOCGIFFLAGS: No such device
    bridge br0 doesn't exist; can't delete it
    Setup bridge...
    device eth0 entered promiscuous mode
    Qos threshold Start
    Qos threshold End
    Disable WAN port Flow Control
    SIOCDELRT: No such process
    br0: port 1(eth0) entering listening state
    br0: port 1(eth0) entering learning state
    SIOCDELRT: No such procebr0: port 1(eth0) entering forwarding state
    ss
    br0: topology change detected, propagating
    SIOCDELRT: No such process
    SIOCDELRT: No such process
    Error in wlanapp.sh, no wlan interface is given!
    Setup WAN interface
    killall: auto-connect: no process killed
    killall: udhcpc: no process killed
    killall: pptp.sh: no process killed
    killall: pppoe.sh: no process killed
    snmpd -c /var/run/snmpd.conf -p /var/run/snmpd.pid UDP:161
    write file: /var/run/sshd.key OK!
    /bin/dropbear -d /var/run/sshd.key -p 22 -P /var/run/dropbear.pid
    [369] Jan 01 00:00:21 Failed reading '/etc/dropbear/dropbear_rsa_host_key', disabling RSA
    WTLPv1.2.11
    major:1 minor:2 bugs:11
    [382] Jan 01 00:00:21 Running in background
    voip flash server share size = 6045
    apimb: mib_get MIB_VOIP_CFG
    /etc/ini
    SW-WTL+ login:

    =============================
    Default Reset (Will Regenerate SSH Key)

    The system is Sending SIGKILL to all processes.
    Please stand by while rebooting the system.
    <0>Restarting system.
    Shutdown network interface
    eth0:===>
    br0: port 1(eth0) entering disabled state
    eth1:===>
    br0:===>
    Enable Watch Dog to Reset whole system

    Eon SPI (8 MByte)!

    DDR DRAM 64 MB @ 195 MHz

    Soundwin (Wagaly Talk Lite Plus) at 2009.06.17-13:28+0800 version v1.5.3 [16bit](390MHz)

    decompressing kernel:
    Uncompressing Linux... done, booting the kernel.
    done decompressing kernel.
    early printk enabled
    Determined physical RAM map:
    memory: 04000000 @ 00000000 (usable)
    Initial ramdisk at: 0x803eb000 (1892352 bytes)
    On node 0 totalpages: 16384
    zone(0): 16384 pages.
    zone(1): 0 pages.
    zone(2): 0 pages.
    Kernel command line: root=/dev/ram console=0 ramdisk_start=0
    Calibrating delay loop... 389.12 BogoMIPS
    Memory: 55220k/65536k available (3598k kernel code, 10316k reserved, 2286k data, 8k init, 0k highmem)
    Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
    Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
    Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
    Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
    Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
    check_wait... unavailable.
    POSIX conformance testing by UNIFIX
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    Starting kswapd
    Serial driver version 6.02 (2003-03-12) with no serial options enabled
    ttyS00 at 0x2000 (irq = 5) is a rtl_uart1
    state->flags=00000000
    Realtek GPIO Driver for Flash Reload Default
    block: 128 slots per queue, batch=32
    RAMDISK driver initialized: 16 RAM disks of 15000K size 1024 blocksize
    PPP generic driver version 2.4.1
    MPPE/MPPC encryption/compression module registered
    SPI INIT
    flash device: 0x400000 at 0xbfe00000
    probe realtek
    get SPI CS0
    maker:1c type:20 sector_cnt:128
    capacity_id = 23
    get SPI CS1
    maker:0 type:0 sector_cnt:0
    capacity_id = 0

    Eon matched!!get SPI chip driver!
    Physically mapped flash: Found an alies 0x800000 for the chip at 0x0, eon device detect.
    probe ends
    probe realtek2
    Creating 1 MTD partitions on "Physically mapped flash":
    0x00000000-0x00800000 : "Wagaly Talk Lite Plus only"
    RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
    Cannot find driver for DiskOnChip Millennium at 0x6000
    usb.c: registered new driver usbdevfs
    usb.c: registered new driver hub
    rtl8652_ehci : irq 7, b8021000
    usb.c: new USB bus registered, assigned bus number 1
    rtl8652_ehci : USB f.f enabled, EHCI 1.00, driver 2003-Dec-29/2.4
    hub.c: USB hub found
    hub.c: 2 ports detected
    host/usb-ohci-rtl8652.c: USB OHCI at membase 0xb8020000, IRQ 7
    host/usb-ohci-rtl8652.c: usb-
    usb.c: new USB bus registered, assigned bus number 2
    hub.c: USB hub found
    hub.c: 2 ports detected
    RTL8192SU driver version 0.2 (2009-05-20)
    usb.c: registered new driver RTL8192SU
    Realtek 865x Ethernet driver v0.6 (Mar 26, 2008)
    Initialize Hardware Tables Driver ......
    chip name: 8196B, chip revid: 2
    eth0: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:11, IRQ 2
    eth1: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:22, IRQ 2
    Realtek FastPath v1.08
    =============RTK VOIP SUITE=============
    INITIAL VOIP MANAGER PROGRAM
    INITIAL VOIP DSP PROGRAM
    RTK VoIP Version: 1.1.1
    IMEM_init_OK
    INIT VAR OK
    === RTP Event Send Tasklet Initialization ===
    ========================================

    ====== RTK PCM Controller Initialization =======
    -------Si3217x Driver Rev 0.1------
    Start SLIC init....
    ( GPIO E ) for SLIC[0]...=> OK !
    SLIC0 ID: Si32178 Revision B
    Starting calibration... ...
    SLIC0 master state check pass!
    Init OK!
    Start DAA init....
    Init OK!
    Request IRQ for PCM Controller OK!.
    ================= FISISH ===============
    <6>NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP, IGMP
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 4096 bind 8192)
    Linux IP multicast router 0.06 plus PIM-SM
    ip_conntrack version 2.1 (512 buckets, 4096 max) - 324 bytes per conntrack
    PPTP netfilter connection tracking: registered
    PPTP netfilter NAT helper: registered
    ip_tables: (C) 2000-2002 Netfilter core team
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    NET4: Ethernet Bridge 008 for NET4.0
    RAMDISK: LZMA Compressed image found at block 0
    Freeing initrd memory: 1848k freed
    VFS: Mounted root (ext2 filesystem).
    Freeing unused kernel memory: 8k freed
    mount /proc file system ok!
    serial console detected. Disabling virtual terminals.
    init started: BusyBox v1.00-pre8 (2009.08.17-05:45+0000) multi-call binary
    write file: /tmp/private_key OK!
    flash voip check
    Setup BRIDGE interface
    killall: syslogd: no process killed
    killall: klogd: no process killed
    SIOCGIFFLAGS: No such device
    bridge br0 doesn't exist; can't delete it
    Setup bridge...
    device eth0 entered promiscuous mode
    Qos threshold Start
    Qos threshold End
    Disable WAN port Flow Control
    SIOCDELRT: No such process
    br0: port 1(eth0) entering listening state
    br0: port 1(eth0) entering learning state
    SIOCDELRT: No such procebr0: port 1(eth0) entering forwarding state
    ss
    br0: topology change detected, propagating
    SIOCDELRT: No such process
    SIOCDELRT: No such process
    Error in wlanapp.sh, no wlan interface is given!
    Setup WAN interface
    killall: auto-connect: no process killed
    killall: udhcpc: no process killed
    killall: pptp.sh: no process killed
    killall: pppoe.sh: no process killed
    snmpd -c /var/run/snmpd.conf -p /var/run/snmpd.pid UDP:161
    No data in flash
    chmod: /var/run/sshd.key: No such file or directory
    Will output 1024 bit dss secret key to '/var/run/sshd.key'
    Generating key, this may take a while...
    Public key portion is:
    ssh-dss 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 root@(none)
    Fingerprint: md5 1f:a0:12:a4:1e:df:57:58:46:87:63:0a:4f:df:fe:dd
    /bin/dropbear -d /var/run/sshd.key -p 22 -P /var/run/dropbear.pid
    [372] Jan 01 00:00:30 Failed reading '/etc/dropbear/dropbear_rsa_host_key', disabling RSA
    WTLPv1.2.11
    major:1 minor:2 bugs:11
    [381] Jan 01 00:00:30 Running in background
    voip flash server share size = 6045
    apimb: mib_get MIB_VOIP_CFG
    apimb: mib_get MIB_VOIP_CFG
    /etc/ini
    SW-WTL+ login:


    附加圖片 附加圖片 wtlp201_front.jpg   wtlp201_back.jpg  
    此文章於 2010-02-07 04:40 AM 被 adamkuo 編輯。

  2. #2
    升級了~讀了3年還 carzyman 的大頭照
    註冊日期
    2001-06-12
    所在地區
    ADSL 8M
    討論區文章
    471

    回覆: 遠傳家用電話節費盒WT-5 (WTLP201)

    不能再加個無線ap.....防火牆....qos等等功能嗎~~~這樣會比較多人愛說
    好的東西----我愛

    好便宜的東西----我也愛
    又好又便宜的東西----我最愛
    所以我愛我自己----又便宜又好用!

  3. #3
    會員
    註冊日期
    2001-04-19
    討論區文章
    161

    回覆: 遠傳家用電話節費盒WT-5 (WTLP201)

    無線ap => +TWD 499買一張專用USB網卡,但是效果不好,可以設定的功能也不多
    防火牆 => 有SPI等基礎防火牆功能,但是不開放設定
    qos => 有但是預設給SIP VoIP用了,其他,不開放設定
    重點是機器非常熱,加熱散熱片後常常是五十度以上的溫度
    所以WT5才把機殼開了一堆洞希望能減緩WT4熱當的問題
    此文章於 2010-02-07 04:47 AM 被 adamkuo 編輯。

  4. #4
    會員
    註冊日期
    2005-10-18
    討論區文章
    228

    回覆: 遠傳家用電話節費盒WT-5 (WTLP201)

    可以接在IP分享器後面嗎?開埠給WT5過,我的是CM上網只有一個孔,
    看看WT5可以接在IP分享器後嗎開埠給他過...???
    目前有測過好像放在IP分享器後面就沒有撥話音了...

  5. #5
    會員
    註冊日期
    2005-02-25
    討論區文章
    290

    回覆: 遠傳家用電話節費盒WT-5 (WTLP201)

    小弟目前也很困擾...不能DMZ,什麼事情都不方便啊....



  6. #6
    會員
    註冊日期
    2005-02-28
    討論區文章
    26

    不錯 回覆: 遠傳家用電話節費盒WT-5 (WTLP201)

    引用 作者:adamkuo 瀏覽文章
    無線ap => +TWD 499買一張專用USB網卡,但是效果不好,可以設定的功能也不多
    防火牆 => 有SPI等基礎防火牆功能,但是不開放設定
    qos => 有但是預設給SIP VoIP用了,其他,不開放設定
    重點是機器非常熱,加熱散熱片後常常是五十度以上的溫度
    所以WT5才把機殼開了一堆洞希望能減緩WT4熱當的問題
    版大真的好專業也很用心...

    昨天才剛剛看完您的發文..

    剛剛又看到你在AM:4:40又添加很多測試資料...

    想必版大的功力一定很深厚...cc

    期待版大後續破解文章...

    造福如我廣大版迷...

    感謝期待中~.....^^"

  7. #7
    會員
    註冊日期
    2005-02-28
    討論區文章
    26

    回覆: 遠傳家用電話節費盒WT-5 (WTLP201)

    版大可以順便說說是如何連上console的嗎? ^^"

    另外..
    小弟對於不能接在分享器後面也是很頭疼 ><..
    不知道是否可以解決呢?

  8. #8
    升級了~讀了3年還 carzyman 的大頭照
    註冊日期
    2001-06-12
    所在地區
    ADSL 8M
    討論區文章
    471

    回覆: 遠傳家用電話節費盒WT-5 (WTLP201)

    引用 作者:deepcolor 瀏覽文章
    版大可以順便說說是如何連上console的嗎? ^^"

    另外..
    小弟對於不能接在分享器後面也是很頭疼 ><..
    不知道是否可以解決呢?
    為何一定要接在分享器後面
    ADSL----->ip分享器--->電腦
    ----->節費器--->電話

    這樣不好嗎....
    好的東西----我愛

    好便宜的東西----我也愛
    又好又便宜的東西----我最愛
    所以我愛我自己----又便宜又好用!

  9. #9
    會員
    註冊日期
    2001-04-19
    討論區文章
    161

    回覆: 遠傳家用電話節費盒WT-5 (WTLP201)

    直接接電路板Console Pins就可以看到上述畫面 38400,N,8,1
    不過這一台不用接Console Port
    直接用SSH連線就可以了~雖然看不到開機訊息但是看了也沒差吧~
    沒有中斷模式只能乖乖看他開機然後進入Login提示~
    用SSH連線也是直接卡在login提示~

    接在分享器後面可以註冊跟撥號
    但是由於這台機器沒開放STUN也沒有SIP Proxy等SIP over NAT功能
    如果你的分享器沒有SIP ALG的話,是沒有辦法正常運作的
    只聽得到撥號音(因為是機器產生的)但是會聽不到傳回來的聲音
    因為WT5註冊是會回報WAN IP給SBC Server,但是在NAT後會取得虛擬IP
    SIP/RTP Server的資料便不知到要回傳到哪裡
    在WT5不開放SIP over NAT時就要靠有SIP ALG的分享器將封包中虛擬IP改成分享器WAN IP 並建立port mapping

    引用 作者:deepcolor 瀏覽文章
    版大可以順便說說是如何連上console的嗎? ^^"

    另外..
    小弟對於不能接在分享器後面也是很頭疼 ><..
    不知道是否可以解決呢?
    此文章於 2010-02-08 01:06 AM 被 adamkuo 編輯。

  10. #10
    會員
    註冊日期
    2005-02-28
    討論區文章
    26

    微笑 回覆: 遠傳家用電話節費盒WT-5 (WTLP201)

    引用 作者:carzyman 瀏覽文章
    為何一定要接在分享器後面
    ADSL----->ip分享器--->電腦
    ----->節費器--->電話

    這樣不好嗎....
    carzyman兄.... 想必是沒有申請WT5吧

    目前遠傳的WT5只要不是直接接在ADSL的小烏龜上面取得對外IP上網的話

    是一律都沒有辦法正常接聽撥打電話的!

    這也是許多人安裝後最頭痛的地方了~!!

    希望可以透過修改韌體的方式解決這個令人頭痛的問題...

    神人...快點出來現身吧~!!



第 1 頁,共 10 頁 1 2 3 ... 末頁末頁

類似的主題

  1. 回覆: 19
    最後發表: 2011-10-11, 03:26 PM
  2. 遠傳電話節費盒 有人安裝在弱電箱嗎? 我想只裝一台,全戶節費
    作者:leomichael 所在討論版:-- 網 路 硬 體 版
    回覆: 13
    最後發表: 2010-07-21, 12:48 AM
  3. 有人在用遠傳家用電話節費盒嗎?
    作者:all600 所在討論版:-- 閒 話 家 常 灌 水 版
    回覆: 8
    最後發表: 2010-05-28, 07:45 PM

 

Si3217x linux driver

遠傳節費盒 wt-5 usb wi-fi

SI3217x INIT

SI3217X

遠傳節費盒如何開啟T07AW無線網路

t07aw ssh key

家用電話監聽 收費

遠傳省費盒 wifi 到期

遠傳 wt5 支援的 usb wifi

遠傳Seednet - WT5專用Wi-Fi網卡圖片

發表文章規則

  • 不可以發表新主題
  • 不可以回覆文章
  • 不可以上傳附加檔案
  • 不可以編輯自己的文章
  •