剛收到了WT-5
小巧到不行,雖然不是ZyXEL代工了不過用料似乎還不錯
91%鋁質電容!!真是嚇死人~
主處理器單一一顆Realtek RTL8972B,大部分用在IP Phone中
不過如果要用NAT + Wifi可能就不太夠力
而且沒有散熱片,改天去買一片加上去
中規中矩的8MB SPI Flash,可惜沒有什麼第三方韌體也沒有Opensource.
超大容量64MB Memory當SIP ATA絕對足夠
正面圖
[IMG]http://www.pczone.com.tw/attachment.php?attachmentid=19819&stc=1&d=1264960087[/IMG]
背面圖
[IMG]http://www.pczone.com.tw/attachment.php?attachmentid=19820&stc=1&d=1264960087[/IMG]
備用圖
正面圖
[IMG]http://farm3.static.flickr.com/2738/4310884989_2487b1cc3c.jpg[/IMG]
背面圖
[IMG]http://farm5.static.flickr.com/4026/4319576356_0b305c2aef.jpg[/IMG]
以上
2010-02-07
Console Boot Message 38400,N,8,1
密碼研究中
Normal Boot / Software Reset
Eon SPI (8 MByte)!
DDR DRAM 64 MB @ 195 MHz
Soundwin (Wagaly Talk Lite Plus) at 2009.06.17-13:28+0800 version v1.5.3 [16bit](390MHz)
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initial ramdisk at: 0x803eb000 (1892352 bytes)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=0 ramdisk_start=0
Calibrating delay loop... 389.12 BogoMIPS
Memory: 55220k/65536k available (3598k kernel code, 10316k reserved, 2286k data, 8k init, 0k highmem)
Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x2000 (irq = 5) is a rtl_uart1
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 15000K size 1024 blocksize
PPP generic driver version 2.4.1
MPPE/MPPC encryption/compression module registered
SPI INIT
flash device: 0x400000 at 0xbfe00000
probe realtek
get SPI CS0
maker:1c type:20 sector_cnt:128
capacity_id = 23
get SPI CS1
maker:0 type:0 sector_cnt:0
capacity_id = 0
Eon matched!!get SPI chip driver!
Physically mapped flash: Found an alies 0x800000 for the chip at 0x0, eon device detect.
probe ends
probe realtek2
Creating 1 MTD partitions on "Physically mapped flash":
0x00000000-0x00800000 : "Wagaly Talk Lite Plus only"
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Cannot find driver for DiskOnChip Millennium at 0x6000
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
rtl8652_ehci : irq 7, b8021000
usb.c: new USB bus registered, assigned bus number 1
rtl8652_ehci : USB f.f enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 2 ports detected
host/usb-ohci-rtl8652.c: USB OHCI at membase 0xb8020000, IRQ 7
host/usb-ohci-rtl8652.c: usb-
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
RTL8192SU driver version 0.2 (2009-05-20)
usb.c: registered new driver RTL8192SU
Realtek 865x Ethernet driver v0.6 (Mar 26, 2008)
Initialize Hardware Tables Driver ......
chip name: 8196B, chip revid: 2
eth0: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:11, IRQ 2
eth1: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:22, IRQ 2
Realtek FastPath v1.08
=============RTK VOIP SUITE=============
INITIAL VOIP MANAGER PROGRAM
INITIAL VOIP DSP PROGRAM
RTK VoIP Version: 1.1.1
IMEM_init_OK
INIT VAR OK
=== RTP Event Send Tasklet Initialization ===
========================================
====== RTK PCM Controller Initialization =======
-------Si3217x Driver Rev 0.1------
Start SLIC init....
( GPIO E ) for SLIC[0]...=> OK !
SLIC0 ID: Si32178 Revision B
Starting calibration... ...
SLIC0 master state check pass!
Init OK!
Start DAA init....
Init OK!
Request IRQ for PCM Controller OK!.
================= FISISH ===============
<6>NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (512 buckets, 4096 max) - 324 bytes per conntrack
PPTP netfilter connection tracking: registered
PPTP netfilter NAT helper: registered
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
RAMDISK: LZMA Compressed image found at block 0
Freeing initrd memory: 1848k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 8k freed
mount /proc file system ok!
serial console detected. Disabling virtual terminals.
init started: BusyBox v1.00-pre8 (2009.08.17-05:45+0000) multi-call binary
write file: /tmp/private_key OK!
flash voip check
Setup BRIDGE interface
killall: syslogd: no process killed
killall: klogd: no process killed
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth0 entered promiscuous mode
Qos threshold Start
Qos threshold End
Disable WAN port Flow Control
SIOCDELRT: No such process
br0: port 1(eth0) entering listening state
br0: port 1(eth0) entering learning state
SIOCDELRT: No such procebr0: port 1(eth0) entering forwarding state
ss
br0: topology change detected, propagating
SIOCDELRT: No such process
SIOCDELRT: No such process
Error in wlanapp.sh, no wlan interface is given!
Setup WAN interface
killall: auto-connect: no process killed
killall: udhcpc: no process killed
killall: pptp.sh: no process killed
killall: pppoe.sh: no process killed
snmpd -c /var/run/snmpd.conf -p /var/run/snmpd.pid UDP:161
write file: /var/run/sshd.key OK!
/bin/dropbear -d /var/run/sshd.key -p 22 -P /var/run/dropbear.pid
[369] Jan 01 00:00:21 Failed reading '/etc/dropbear/dropbear_rsa_host_key', disabling RSA
WTLPv1.2.11
major:1 minor:2 bugs:11
[382] Jan 01 00:00:21 Running in background
voip flash server share size = 6045
apimb: mib_get MIB_VOIP_CFG
/etc/ini
SW-WTL+ login:
=============================
Default Reset (Will Regenerate SSH Key)
The system is Sending SIGKILL to all processes.
Please stand by while rebooting the system.
<0>Restarting system.
Shutdown network interface
eth0:===>
br0: port 1(eth0) entering disabled state
eth1:===>
br0:===>
Enable Watch Dog to Reset whole system
Eon SPI (8 MByte)!
DDR DRAM 64 MB @ 195 MHz
Soundwin (Wagaly Talk Lite Plus) at 2009.06.17-13:28+0800 version v1.5.3 [16bit](390MHz)
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initial ramdisk at: 0x803eb000 (1892352 bytes)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=0 ramdisk_start=0
Calibrating delay loop... 389.12 BogoMIPS
Memory: 55220k/65536k available (3598k kernel code, 10316k reserved, 2286k data, 8k init, 0k highmem)
Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x2000 (irq = 5) is a rtl_uart1
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 15000K size 1024 blocksize
PPP generic driver version 2.4.1
MPPE/MPPC encryption/compression module registered
SPI INIT
flash device: 0x400000 at 0xbfe00000
probe realtek
get SPI CS0
maker:1c type:20 sector_cnt:128
capacity_id = 23
get SPI CS1
maker:0 type:0 sector_cnt:0
capacity_id = 0
Eon matched!!get SPI chip driver!
Physically mapped flash: Found an alies 0x800000 for the chip at 0x0, eon device detect.
probe ends
probe realtek2
Creating 1 MTD partitions on "Physically mapped flash":
0x00000000-0x00800000 : "Wagaly Talk Lite Plus only"
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Cannot find driver for DiskOnChip Millennium at 0x6000
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
rtl8652_ehci : irq 7, b8021000
usb.c: new USB bus registered, assigned bus number 1
rtl8652_ehci : USB f.f enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 2 ports detected
host/usb-ohci-rtl8652.c: USB OHCI at membase 0xb8020000, IRQ 7
host/usb-ohci-rtl8652.c: usb-
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
RTL8192SU driver version 0.2 (2009-05-20)
usb.c: registered new driver RTL8192SU
Realtek 865x Ethernet driver v0.6 (Mar 26, 2008)
Initialize Hardware Tables Driver ......
chip name: 8196B, chip revid: 2
eth0: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:11, IRQ 2
eth1: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:22, IRQ 2
Realtek FastPath v1.08
=============RTK VOIP SUITE=============
INITIAL VOIP MANAGER PROGRAM
INITIAL VOIP DSP PROGRAM
RTK VoIP Version: 1.1.1
IMEM_init_OK
INIT VAR OK
=== RTP Event Send Tasklet Initialization ===
========================================
====== RTK PCM Controller Initialization =======
-------Si3217x Driver Rev 0.1------
Start SLIC init....
( GPIO E ) for SLIC[0]...=> OK !
SLIC0 ID: Si32178 Revision B
Starting calibration... ...
SLIC0 master state check pass!
Init OK!
Start DAA init....
Init OK!
Request IRQ for PCM Controller OK!.
================= FISISH ===============
<6>NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (512 buckets, 4096 max) - 324 bytes per conntrack
PPTP netfilter connection tracking: registered
PPTP netfilter NAT helper: registered
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
RAMDISK: LZMA Compressed image found at block 0
Freeing initrd memory: 1848k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 8k freed
mount /proc file system ok!
serial console detected. Disabling virtual terminals.
init started: BusyBox v1.00-pre8 (2009.08.17-05:45+0000) multi-call binary
write file: /tmp/private_key OK!
flash voip check
Setup BRIDGE interface
killall: syslogd: no process killed
killall: klogd: no process killed
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth0 entered promiscuous mode
Qos threshold Start
Qos threshold End
Disable WAN port Flow Control
SIOCDELRT: No such process
br0: port 1(eth0) entering listening state
br0: port 1(eth0) entering learning state
SIOCDELRT: No such procebr0: port 1(eth0) entering forwarding state
ss
br0: topology change detected, propagating
SIOCDELRT: No such process
SIOCDELRT: No such process
Error in wlanapp.sh, no wlan interface is given!
Setup WAN interface
killall: auto-connect: no process killed
killall: udhcpc: no process killed
killall: pptp.sh: no process killed
killall: pppoe.sh: no process killed
snmpd -c /var/run/snmpd.conf -p /var/run/snmpd.pid UDP:161
No data in flash
chmod: /var/run/sshd.key: No such file or directory
Will output 1024 bit dss secret key to '/var/run/sshd.key'
Generating key, this may take a while...
Public key portion is:
ssh-dss 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 root@(none)
Fingerprint: md5 1f:a0:12:a4:1e:df:57:58:46:87:63:0a:4f:df:fe:dd
/bin/dropbear -d /var/run/sshd.key -p 22 -P /var/run/dropbear.pid
[372] Jan 01 00:00:30 Failed reading '/etc/dropbear/dropbear_rsa_host_key', disabling RSA
WTLPv1.2.11
major:1 minor:2 bugs:11
[381] Jan 01 00:00:30 Running in background
voip flash server share size = 6045
apimb: mib_get MIB_VOIP_CFG
apimb: mib_get MIB_VOIP_CFG
/etc/ini
SW-WTL+ login: