| 會員  | 回覆: 中華電信VDSL數據機? 最近我家這邊 VDSL(872HA) 以滿年限 設備通通換新 VDSL2 就是D-LINK 這台新的 拍了一些 內部 還看 到USB 沒裝上去     用料真是誇張的多(猜測之後可能會拿掉部份 零組件) 在補它 外觀 雙面洞洞裝 (只能站起來)    連線品質 (內部太多設定了 看無 所以跳過)  ============連接線進入========================== U-Boot 1.1.4.8.f8r32 for FUSIV chipset by Ikanos(Mar 30 2009 - 08:21:49) CPU: IKANOS Fusiv 180 Family DRAM: 32 MB Flash: 8 MB In: serial Out: serial Err: serial Net: Registered Ethernet Driver voxEmac Type "h" for HELP. Have fun! Hit any key to stop autoboot: 0 ## Booting image from active region 2 at bfc10000 ... Image Name: Ikanos_kernel_2.6.18.2 Created: 2009-10-07 9:16:51 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 746281 Bytes = 728.8 kB Load Address: 80010000 Entry Point: 8022e000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Linux version 2.6.18.8 ([email protected]) (gcc version 3.4.3) #1 P REEMPT Wed Oct 7 17:14:51 CST 2009 arg[1] root=/dev/mtdblock6 CPU revision is: 0001964c Determined physical RAM map: memory: 01800000 @ 00000000 (usable) Built 1 zonelists. Total pages: 6144 Kernel command line: root=/dev/mtdblock6 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled PID hash table entries: 128 (order: 7, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 21848k/24576k available (1879k kernel code, 2728k reserved, 284k data, 1 48k init, 0k highmem) Mount-cache hash table entries: 512 Checking for 'wait' instruction... available. NET: Registered protocol family 16 Fusiv PCI: starting... NET: Registered protocol family 2 IP route cache hash table entries: 256 (order: -2, 1024 bytes) TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 512 (order: -1, 2048 bytes) TCP: Hash tables configured (established 1024 bind 512) TCP reno registered Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher LZMA decompressor support based on LZMA SDK 4.05 by Oleg I.Vdovikin devfs: 2004-01-31 Richard Gooch ([email protected]) devfs: boot_options: 0x1 Initializing Cryptographic API io scheduler noop registered (default) Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0xb9020000 (irq = 6) is a 16450 nbd: registered device at major 43 PPP generic driver version 2.4.2 NET: Registered protocol family 24 On Board flash device: 0x800000 at 0x1f800000 ELBOX physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. [ACTIVE REGION]: 2 ELBOX physically mapped flash: squashfs filesystem found at block 4928 Creating 8 MTD partitions on "ELBOX physically mapped flash": 0x00000000-0x00030000 : "uboot" 0x00004000-0x00008000 : "ubootconfig" 0x007f0000-0x00800000 : "rgdb" 0x00030000-0x00800000 : "firmware(reserve)" 0x00030000-0x00410000 : "upgrade" 0x004d0020-0x0078e020 : "rootfs" 0x00410000-0x007f0000 : "upgrade2" 0x00000000-0x00800000 : "flash" ip_conntrack version 2.4 (192 buckets, 1536 max) - 312 bytes per conntrack ip_tables: (C) 2000-2006 Netfilter Core Team ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <[email protected]> All bugs added by David S. Miller <[email protected]> VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 148k freed init started: BusyBox v1.00 (2009.10.06-11:50+0000) multi-call binary [/etc/init.d/S03config.sh] Mounting proc and var ... Start xmldb ... [/etc/scripts/misc/profile.sh] init ... [/etc/scripts/misc/profile_action.sh] get ... [/etc/scripts/misc/defnodes.sh] ... SH [/etc/defnodes/S10syncnodes.sh] ... SH [/etc/defnodes/S11setext.sh] ... PHP [/etc/defnodes/S12setnodes.php] ... SH [/etc/defnodes/S13setext.sh] ... [/etc/defnodes/S13setext.sh] ... PHP [/etc/defnodes/S14setnodes.php] ... SH [/etc/defnodes/S15syncnodes.sh] ... PHP [/etc/defnodes/S20setnodes.php] ... SH [/etc/defnodes/S20upnp_igd.sh] ... SH [/etc/defnodes/S22setext.sh] ... SH [/etc/defnodes/S30setnode.sh] ... PHP [/etc/defnodes/S40brand.php] ... SH [/etc/defnodes/S40syncnodes.sh] ... : cannot createpv4/neigh/default/gc_thresh1 : cannot createpv4/neigh/default/gc_thresh2 SH [/etc/defnodes/S41setext.sh] ... PHP [/etc/defnodes/S42setnodes.php] ... [/etc/scripts/misc/defnodes.sh] Done !! [/etc/templates/timezone.sh] ... [/etc/templates/logs.sh] ... [/var/run/logs_run.sh] ... Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/ap_code/lib/fusivlib_lkm.ko fusivlib_lkm: module license 'proprietary' taints kernel. fusiv library initializing... Buffer Copy Through DMA is enabled fusiv library initialized SUCCESSFULLY... Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/bm/bmdriver_lkm.ko Buffer Manager is initializing... BMU GIGE clock Slave Mem Alloc: Req size 32 Ptr2Block 0x191f0000 Load into BM APU Successful !!! Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/timerlib/timers_lkm. ko Timers are getting initalized Timers are initilized SUCCESSFULLY... Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/ap2ap/ap2ap_lkm.ko AP2AP fastpath initialized SUCCESSFULLY... Added AP PREROUTE Hook Added AP POSTROUTE Hook Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/dri vers/ethdriver/ethdriver_lkm.ko eth0: Netpro Sierra Ethernet found at 0xb9110000, irq 14 GIGE 1 clock dev->baseAddr b9110000 Slave Mem Alloc: Req size 32 Ptr2Block 0x191f0020 eth1: Netpro Sierra Ethernet found at 0xb9150000, irq 13 GIGE 2 clock dev->baseAddr b9150000 Slave Mem Alloc: Req size 32 Ptr2Block 0x191f0040 Ethernet Driver is initialized SUCCESSFULLY Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/switch/icplus/ip175d _lkm.ko Found IC+ 175d switch hardware ICPLUS registered to ethernet port eth0 Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/ethdriver/sysKCode_l km.ko Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/peri_ap/periap_drive r_lkm.ko periApDriverInit: doneSlave Mem Alloc: Req size 32 Ptr2Block 0x191f0060 *******LOAD firmware to AP:PERI_ID result:0Load into PERI_AP APU Successful !!! Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/pppoe_passthru/pppoe Passthrough_lkm.ko ***** PPP over Ethernet Relay driver registered with Major number: 253 ***** Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/ipqos/ipqos_lkm.ko System Speed is 166MHz Enable IRQ for IPQOS timer Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/opensrc/opensrc_lkm. ko Using /lib/modules/2.6.18.8/kernel/bmedrv_init: Registered BME device with Major number 252 fusbmedrv_init: Region 0x01800000 - 0x01ffffff allocated successfully ivBME Driver has been loaded SUCCESSFULLY _src/kernel/drivers/bmedriver/bmedrv.ko Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/vdsldriver/vdsldrive r_lkm.ko VDSL AP and VDSL PHY clocks are enabled eth2: Netpro VDSL Ethernet found at 0x0, irq 36 VDSL PHY default parameters configured successfully User parameters for VDSL AP configured successfully Slave Mem Alloc: Req size 32 Ptr2Block 0x191f0080 VDSL AP started successfully default parameters configured successfully VDSL Driver is initialized SUCCESSFULLY Using lib/modules/ifx_nfext_core.ko CPE start address is a1800000 ipos system initialized Using lib/modules/ifx_oam.ko Loading Factory Reset driver Using /lib/modules/freset.ko BME 1 is coming up b1p0 iposBmeStartBlk cmdtag 0 status: IN PROGRESS cpe> No wireless device Transfer to SDRAM Successful BmeHw: Downloading BME 1 software..... BmeHw: Bme 1 software code downloaded successfully b1p0 iposBmeStartBlk cmdtag 0 status: COMPLETE cpe> Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/policyVlan/vlan _classifier_lkm.ko vlan_classifier_lkm module loaded SUCCESSFULLY... Using /lib/modules/2.6.18.8/kernel/fusiv_src/kernel/drivers/igmpsnoop/igmpsnoop_ lkm.ko IGMP Snoop Module inserted successfully Loading LED driver Using /lib/modules/drv_led_lkm.ko Using /lib/modules/ifresetcnt.ko Network interface reset count v1.0 [/etc/templates/timezone.sh] ... Sat Jan 1 16:00:10 PST 2000 [/etc/templates/timezone.sh] ... Sat Jan 1 00:00:00 PST 2000 [/etc/init.d/S03config.sh] done! [/etc/init.d/S10system.sh] [/etc/templates/vlan.sh] [start]... alm freq 20 status freq 30 b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS cpe> b1p0 iposPeriodicReportEnable cmdtag 99 status: COMPLETE cpe> [/var/run/vlan_start.sh] ... Start Switch LAN setting disable switch vlan feature... [/etc/scripts/layout.sh] [start] ... [/var/run/layout_start.sh] ... Start router layout ... device eth0 entered promiscuous mode br0: port 1(eth0) entering learning state br0: topology change detected, propagating br0: port 1(eth0) entering forwarding state [/etc/templates/wan_vlan.sh] [start] ... [/var/run/wan_vlan_start.sh] ... Start WAN VLAN ... Set name-type for VLAN subsystem. Should be visible in /proc/net/vlan/config [/etc/templates/lan.sh] [start] ... [/var/run/lan_start.sh] ... Start LAN ( br0/192.168.1.1/255.255.255.0.)... DHCP server is disabled! [/etc/templates/thttpd.sh] [start] ... Starting THTTPD ... [/etc/templates/webs.sh] [start] ... auto ,en ,dir = /www [/var/run/webs_start.sh] ... Starting HTTPD ... UPnP is disabled ! [/etc/templates/logd.sh] ... OamOptionMask Set to 3 Please execute 'vdsl' in 1 seconds to enter into Supervisor mode [/var/run/logd_start.sh] ... Starting logd ... >>> ALPHA Log: /bin/alphaLogd: create logd_ipc(3) OK ! [/etc/templates/rg.sh] [start] [] [] [] []... [/var/run/rg_start.sh] ... 0 sendto_unsock(/var/run/portt.unixsocket, flush) [/etc/templates/tftpd.sh] [restart] ... [/var/run/tftpd_start.sh] ... Starting tftpd ... [/etc/templates/housekeeper.sh] [start] ... [/var/run/housekeeper_start.sh] ... Starting housekeeper ... [/etc/templates/dns.sh] [start] ... [/var/run/dns_start.sh] ... Changing port profile #2 BAND_PLAN=0x1 PTM MODE=0x0 OamoptionMask 3 optionMask 8 b1p0 iposBmeProvision cmdtag 0 status: IN PROGRESS cpe> [/etc/templates/dnrd.sh] [start] [] ... b1p0 iposBmeProvision cmdtag 0 status: COMPLETE cpe> b1p1 iposPmConfig cmdtag 0 status: IN PROGRESS cpe> b1p1 iposPmConfig cmdtag 0 status: COMPLETE cpe> [/var/run/dnrd_start.sh] ... Start DNRD ... Notice: caching turned off [/etc/templates/upnpd.sh] [start] ... [/var/run/upnpd_start.sh] ... UPNP function is not enabled !! [/etc/templates/proto_vlan.sh] [start] ... [/var/run/proto_vlan_start.sh] ... [/etc/templates/dhcp_option.sh] [start] ... : cannot create [/etc/templates/flash_agent.sh] [start] ... [/var/run/flash_agent_start.sh] ... >>> ALPHA Flash Agent: 00:00:04 FLASHAGENT: Create fa_r_fa_ipc(4) OK ! [/etc/templates/diap.sh] [start] ... [/var/run/diap_start.sh] ... Starting DIAP ... [/etc/templates/telnetd.sh] [start] ... [/var/run/telnetd_start.sh] ... Starting telnetd ... [/etc/templates/sshd.sh] [start] ... [/var/run/sshd_start.sh] ... Starting SSH ... [1066] Jan 01 00:00:04 Running in background [/etc/templates/oam_snoop.sh] [start] ... [/var/run/oam_snoop_start.sh] ... Enable ALPHA OAM parser ... [/etc/templates/tr069.sh] [start] ... [/var/run/tr069_start.sh] ... Starting TR069, but Disable ... [/etc/templates/snmp.sh] [start] ... [/var/run/snmp_start.sh] ... Starting SNMP ... SNMP is disabled! [/etc/templates/igmpsnoop.sh] [start] ... enable igmpsnooping of 175D [/var/run/igmpsnoop_start.sh] ... [/etc/templates/cfm.sh] [start] ... [/var/run/cfm_start.sh] ... Enable ALPHA CFM ... [/etc/templates/tftpd.sh] [start] ... [/var/run/tftpd_stop.sh] ... [/var/run/tftpd_stop.sh] ... [/var/run/tftpd_start.sh] ... Starting tftpd ... [/etc/templates/alg.sh] start ... Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_conntrack_h323.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_nat_h323.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_conntrack_ipsec.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_nat_ipsec.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_nat_snmp_basic.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_conntrack_irc.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_nat_irc.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_conntrack_ftp.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_nat_ftp.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_conntrack_tftp.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_nat_tftp.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_conntrack_amanda.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_nat_amanda.ko Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_conntrack_pptp.ko ip_conntrack_pptp version 3.1 loaded Using /lib/modules/2.6.18.8/kernel/net/ipv4/netfilter/ip_nat_pptp.ko ip_nat_pptp version 3.0 loaded [/etc/init.d/S10system.sh] done! rcS done! login: DSL-6541k Configure Menu 01. WAN 02. LAN 03. VLAN 04. VDSL2 05. DNS 06. Dynamic DNS 07. DHCP Server 08. Option Map to DHCP 09. Filter 10. QoS 11. Virtual Server 12. Routing 13. TR069 14. SNMP 15. IGMP 16. Misc 17. LoopBack Test 18. CFM 19. Configuration 20. Firmware Information -> 下一個目標 挑戰加大RAM (32MB RAM 好像就很夠用了) 此篇文章於 2010-06-27 03:52 PM 被 bzip 編輯。. |
| 回覆 |
| 會員 | 回覆: 中華電信VDSL數據機? 感謝你分享,有你真好~ |
| 回覆 |
| 沒事多喝水  | 回覆: 中華電信VDSL數據機? 能看到數據真好！ 5540C都看到不數據~ |
| 回覆 |
| 靜心，拒絕再浪潮  | 回覆: 中華電信VDSL數據機? P874 你即時通上傳檔案 封包會被狗吃掉 所以傳過去的檔案對方開不起來 會出現損毀了 |
| 回覆 |
| XML | RSS 2.0 | RSS |
本論壇所有文章僅代表留言者個人意見，並不代表本站之立場，討論區以「即時留言」方式運作，故無法完全監察所有即時留言，若您發現文章可能有異議，請 email :[email protected] 處理。
