會員 | [問題]freebsd 設定hinet計時制 pppoe 哀 搞的我頭大.... 看書設定 rc.conf 還有ppp.conf 但是都沒用...... 我知道這問題很笨....但是沒辦法 硬著頭皮問 我的網路卡是3com 905c 我照書本裡面打的 ppp.conf 語法: default: set log Phase Chat LCP IPCP CCP tun command nat enable yes nat same_ports yes nat use_sockets yes set redial 15 28800 set reconnect 15 28800 pppoe: set device PPPoE:xl0: set mru 1492 set mtu 1492 set speed sync enable lqr set lqrperiod 5 set cd 5 set dial set login set timeout 0 set authname 我hinet帳號 set authkey 我的密碼 set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0 add default HISADDR enable dns 語法: network_interfaces="auto" ifconfig_xl0="inet 10,0,0,1 netmask 255.0.0.0 -arp up" ppp_enable="YES" ppp_mode="ddial" ppp_profile="pppoe" defaultrouter="10.0.0.1" gateway_enable="YES" 後 會出現 pppoe ON LOCALHOST>> 我就不知道要x嘛了....哀 請教教我吧~ |
回覆 |
會員 | 1. First you must change to the kernel configuration directory: cd /usr/src/sys/i386/conf 2. In the kernel configuration directory, use your favorite text editor and edit the kernel file. For example, if you use emacs, you would type: emacs KERNEL 3. Go to the end of the kernel file and add the following three lines: options NETGRAPH options NETGRAPH_PPPOE options NETGRAPH_SOCKET 4. After adding these three lines, save the modified kernel file. 5. Type this command to set the kernel configuration: config KERNEL 6. Now you must change to the kernel setup directory: cd ../../compile/KERNEL 7. In the kernel setup directory, type the following three commands: make depend make make install Your kernel is now ready for PPPoE! Configuring FreeBSD /etc/ppp/ppp.conf File To edit the /etc/ppp/ppp.conf file, just use your favorite text editor. Replace any existing file content with the lines below. Be sure the "set device PPPoE:---" line is correct for your network interface card. (We used ed1 for the NIC in this example.) Change the authname and authkey to your sympatico user id (b1xxxxxx) and your password. # /etc/ppp/ppp.conf default: set log Phase Chat LCP IPCP CCP tun command nat enable yes nat same_ports yes nat use_sockets yes set redial 15 28800 set reconnect 15 28800 pppoe: set device PPPoE:ed1: set mru 1492 set mtu 1492 set speed sync set speed sync enable lqr set lqrperiod 5 set cd 5 set dial set login set timeout 0 set authname [email protected] set authkey yourpassword set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0 add default HISADDR enable dns # end of ppp configuration Configuring FreeBSD /etc/rc.conf?File The /etc/rc.conf file should be set up as follows for the ethernet interface that goes to your DSL modem. (Again, this example uses ed1 for the NIC.) # /etc/rc.conf # /etc/rc.conf network_interfaces="auto"巠 #Set network interfaces automatically ifconfig_ed1="inet 10.0.0.1 netmask 255.0.0.0 -arp up" ppp_enable="YES" #This enables PPP on startup (recommended) ppp_mode="background" ppp_profile="pppoe" #end of?/etc/rc.conf Rebooting the System After you have compiled the kernel to support PPPoE and have edited the /etc/ppp/ppp.conf and /etc/rc.conf files with the right configuration, you can reboot your system. If you enabled ppp in the /etc/rc.conf as recommende /etc/rc.conf file, you can use this command to connect to the Internet manually: . vi /etc/rc.conf ppp_enable="YES" ppp_mode="ddial" ppp_profile="pppoe" 試試看吧我朋友給我的,我還沒設過 |
回覆 |
會員 | 我解決了 原來是我新買的 3com 905c網路卡 根本是不能用.... 害我搞半天 謝謝回覆~ |
回覆 |
獎金獵人 | 原本想說幫你一個忙得... 沒想到你已經OK姥...@@ 之前我也常常有網路方面的困擾... 您有買那本黑色的書嗎? |
回覆 |
主題工具 | |
|
類似的主題 | ||||
主題 | 主題作者 | 討論版 | 回覆 | 最後發表 |
【問題】TECOM WL5401 PPPoE 問題 | ryoichi | -- 網 路 硬 體 版 | 0 | 2009-02-07 04:56 PM |
【教學】自動重撥 PPPoE ADSL 連線 (For Linux & FreeBSD) | dekuo | -- FreeBSD & Linux 討 論 版 | 17 | 2009-01-20 10:09 PM |
PPPoE?? | chuang7318 | ---- ADSL 軟 硬 體 技 術 | 1 | 2002-01-23 06:46 PM |
PPPoE 資料量會比固接的大嗎? | yusiung | ---- ADSL 軟 硬 體 技 術 | 2 | 2001-06-20 08:34 PM |
PPPoE 何處可以下載呢? | jecy | ---- ADSL 軟 硬 體 技 術 | 1 | 2001-05-08 10:12 PM |
XML | RSS 2.0 | RSS |
本論壇所有文章僅代表留言者個人意見,並不代表本站之立場,討論區以「即時留言」方式運作,故無法完全監察所有即時留言,若您發現文章可能有異議,請 email :[email protected] 處理。