STOP: 0x0000006B

[alu]

安裝win2000出現的錯誤訊息

STPP:0x0000006B (0xC000003A,0x00000002,0x0000000,0x00000000)
PROCESS1_INITIAIZATION_FAILED
If this is the first time you've seen this stop error screen,restant
your computer,If this screen appars again,follow these steps:

Check to make sure any new hardware or software is properly installed.

If this is a new installation ,ask you hardware or software

Manufacturer for any windows 2000 updates you might need.

If problems continue,disable or remove any newly installed hardware or

software.

Disable Bios memory options such as coching or shadowing.

If you need to use safe mode to remove or disable components,restart

your computer,press F8 to select Advanced Startup Options, and them

select safe mode.

Refer to your Getting Started manual for more information on

trouleshooting Stop errors.

有誰知道該如何解決?

[alu]

沒有,但是安裝win xp卻很正常同樣都是NTFS格式,同樣的配備

[rEdS]

你的配備能列個清單嗎?

[daryl]

最初由 alu 發表
安裝win2000出現的錯誤訊息

STPP:0x0000006B (0xC000003A,0x00000002,0x0000000,0x00000000)
PROCESS1_INITIAIZATION_FAILED
If this is the first time you've seen this stop error screen,restant
your computer,If this screen appars again,follow these steps:

Check to make sure any new hardware or software is properly installed.

If this is a new installation ,ask you hardware or software

Manufacturer for any windows 2000 updates you might need.

If problems continue,disable or remove any newly installed hardware or

software.

Disable Bios memory options such as coching or shadowing.

If you need to use safe mode to remove or disable components,restart

your computer,press F8 to select Advanced Startup Options, and them

select safe mode.

Refer to your Getting Started manual for more information on

trouleshooting Stop errors.

有誰知道該如何解決?

我也碰到了相同的問題!
電腦配備如下：
主機板--Gigabyte 7zxe
CPU--duron 1G(無超頻)
Memory--創見128mb(PC133)X2條
VGA--ASUS V7100
Sound card--瑞麗春之頌
網路卡--MELCO LGY-PCI-TXL Fast Ethernet Adapter
另外有安裝V-GEAR MyVCD TV plus
HDD--Maxtor 15GB
光碟機--聯積50X CD-ROM & Traxdata 16X CD-RW

以上的配備在安裝windows 98se 沒問題!
希望有人可以幫小弟診斷一下出了什麼問題!
謝謝!

[flyup]

主機板CPU附近電容器燒毀！！

[Schnaufer]

　　你所列出的錯誤訊息畫面已經有簡略的處理方式說明。而以下所列出的則是 Windows 2000 Support Tools 中的 Error and Event Messages 說明檔所查到的。

STOP: 0x0000006B (parameter, parameter, parameter, parameter) PROCESS1_INITIALIZATION_FAILED

Explanation:
　　This is a Windows 2000 Executive character-mode STOP message. Phase 1 process initialization failed. This can only happen during the relatively short period of time that the Windows 2000 Executive is being initialized, during phase 4 of Windows 2000 startup. There might be a problem with a device driver.

User Action:
　　If this is the first time you have booted after installing new hardware, remove the hardware and boot again. Check the Microsoft Hardware Compatibility List to verify that the hardware and its drivers are compatible with Windows 2000. For information about the hardware, contact the supplier. If you are installing Windows 2000 for the first time, check the Windows 2000 system requirements, including the amount of RAM and disk space required to load the operating system. Also, check the Hardware Compatibility List to verify that the system can run Windows 2000. If Windows 2000 is loaded and no new hardware has been installed, reboot with recovery options set to create a dump file. If the message continues to appear, select the Last Known Good option when you reboot. If there is no Last Known Good configuration, try using the Emergency Repair Disk. If you do not have an Emergency Repair Disk, contact your technical support group.

　　不過同樣的錯誤訊息若發生在舊版 WinNT，原因可能是有某些遺失的 system file，通常是位於 \winnt 或是 \winnt\system32 目錄下的檔案。

　　另外，在安裝 Service Pack 也有可能發生此種錯誤，請見 "Stop 0x0000006B" After Installing a Windows 2000 Service Pack (Q307012)。

　　因為您並沒有詳細說明是在安裝過程中的哪個階段發生的，故把所有可能的原因列出來。文件也許有些深度，請細心閱讀。