我用的是 Zyxel p642r-51
安裝了PNC v.2.30,裡面有個程式叫Internet Access Wizard
在裡面可以設定用PPPoE連線,我就把一些參數設好以後Reset
642r (想當然他沒自己去連線,因為韌體沒提供)但是再用Telnet
或終端機程式看642r的 Menu 24.1原本應提供642r 的一些狀態
如下:
Menu 24.1 - System Maintenance - Status
Node-Lnk Status TxPkts RxPkts Errors Tx B/s Rx B/s Up Time
1-1483 Up 1763 1580 0 0 0 0:20:57
2 N/A 0 0 0 0 0 0:00:00
3 N/A 0 0 0 0 0 0:00:00
4 N/A 0 0 0 0 0 0:00:00
5 N/A 0 0 0 0 0 0:00:00
6 N/A 0 0 0 0 0 0:00:00
7 N/A 0 0 0 0 0 0:00:00
8 N/A 0 0 0 0 0 0:00:00
Ethernet: WAN:
Status: 10M/Half Duplex Tx Pkts: 1750 Line Status: Up
Collisions: 0 Rx Pkts: 1899 Upstream Speed: 64 kbps
CPU Load = 2.47% Downstream Speed: 512 kbps
Press Command:
COMMANDS: 1-Reset Counters ESC-Exit
卻在用PNC設定使用PPPoE後看 Menu 24.1時,出現一些訊息後就重新
Reset 642r,內容如下:
Data Abort Address : 0x0008CD20
Data Abort Data : 0xE5900004
r0= 0x0008CD20 r1= 0x0001FFC0 r2= 0x00000000 r3= 0xE5900004
r4= 0x0008CD20 r5= 0x001346F0 r6= 0x0001C2D8 r7= 0x00000000
r8= 0x0013472C r9= 0x00000000 r10=0x00001103 fp= 0x00134724
r12=0xE5900004 sp= 0x0001F1B8 lr= 0x00004D7C pc= 0x00011AF8
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
1346f0: 00 00 00 00 00 13 47 30 00 00 00 01 00 08 cd d8 ......G0........
134700: 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 ................
134710: 00 13 47 68 00 00 00 00 00 13 47 58 00 13 47 28 ..Gh......GX..G(
134720: 00 08 ce 70 00 08 cd b0 00 13 47 2c 00 00 00 00 ...p......G,....
134730: 00 00 00 00 00 00 11 03 00 14 8d 84 00 00 00 00 ................
134740: 00 00 11 01 00 00 02 32 00 00 00 00 00 13 47 7c .......2......G|
134750: 00 13 47 5c 00 08 d2 28 00 08 ce 34 00 00 00 00 ..G\...(...4....
134760: 00 00 00 00 00 13 47 68 00 36 a7 c4 00 14 9e e0 ......Gh.6......
134770: 00 13 48 a0 00 13 47 80 00 0e 55 fc 00 08 d1 f4 ..H...G...U.....
134780: 00 34 36 04 60 00 00 13 00 34 36 04 60 00 00 13 .46.`....46.`...
134790: 00 00 00 00 00 03 4b a4 01 00 00 00 00 00 00 00 ......K.........
1347a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
1347b0: 20 31 2d 50 50 50 6f 45 00 20 32 20 20 20 20 20 1-PPPoE. 2
1347c0: 20 00 20 33 20 20 20 20 20 20 00 20 34 20 20 20 . 3 . 4
1347d0: 20 20 20 00 20 35 20 20 20 20 20 20 00 20 36 20 . 5 . 6
1347e0: 20 20 20 20 20 00 20 37 20 20 20 20 20 20 00 20 . 7 .
Bootbase Version: V1.05 | 4/14/2000 13:58:03
RAM: Size = 4096 Kbytes
FLASH: Intel 8M
ZyNOS Version: V2.50(AF.1) | 10/4/2000 9:15:43
Press any key to enter debug mode within 3 seconds.
............................................................
[2J[H[HCopyright (c) 1994 - 2000 ZyXEL Communications Corp.
initialize ch =0, ethernet address: 00:a0:c5:12:38:5f
HWSAR (FPGA) : programming (11969) ... done
HWSAR (FPGA) : testing ... done
Wan Channel init ........ done
Loading ADSL modem F/W
........................................... done
Press ENTER to continue...
RasPPPoE軟體也無法連線
然後用PNC將連線方式設回RFC1483/LLC就一切正常了
希望能提供與想以642r 直接撥號的同好們一點點經驗
(因為我也想用,畢竟有了642r 就要物盡其用,把買310的錢省下來)
 |
回覆時引用此文章
書籤