版主 | 再加問一個問題 , 我的流量好像相反了 ... 輸出好像變成輸入 ..... 還是中文化的人搞錯了 ,如下圖 我不知道 mrtg 中所謂的 out 是指什麼 ? 不過根據我的觀念 , 這是一台 ftp server 的流量圖 , 當 client 登入時進行下載 , 對於 ftp server 應該算是 "上傳"吧 ! 而 "上傳資料 " 基本上對於這台 ftp server 而言應該算是 "輸出" ... 可是圖好像相反 .... 有沒有人可以給各建議 ...... 此外 ,想請問有沒有人找到 MRTG 2.9.17 中文化板 ~~~ |
會員 | 看這篇文章從一頁逐漸增至四頁之多,引起我莫大的興趣,再反覆看了幾次,似乎沒有 router hardware 一樣可以架mrtg,實在小弟這破公司,半個router都沒有,又adsl modem 不屬於仿間可修改的那種,先前想架流量圖最終是無計可施下放棄,今拜讀各位大作下,燃起了一絲絲希望,想請各網友幫我鑑定一下,這樣的環境可以架 mrtg 嗎? 我的環境: adsl 計時制 linux redhat 7.1 作 nat & samba server,兩張卡(對外eth1,對內eth0) 網路內有一個switch hub,沒半個router,我想統計 linux 對外eth1的流量,這樣的設備可以嗎?倘若可以,那替代router 的是linux 嗎?假使 snmp service 由linux擔任,mrtg架在另一台win2000,這樣win2000可正確抓到linux 的流量嗎?真不好意思,想釐清一些觀念 |
會員 | 引用:
若要把兩個設備的流量秀在同一個網頁上 我先執行 perl cfgmaker [email protected] "WorkDir:c:\InetPub\wwwroot\MRTG" --output mrtg.cfg 然後執行 perl cfgmaker [email protected] "WorkDir: c:\InetPub\wwwroot\MRTG" --output mrtg.cfg 可是第二個設備的設定就會蓋過第一個設備的設定說 根本無法加入以上的設定阿∼∼ 是不是那邊設錯了阿 可否詳細告知∼∼我是用WIN2K架設的 | |
會員 | 為何我設定時會有問題呢? perl cfgmarker 會有錯誤 可否教教我一下.. Thank you ... |
會員 | 引用:
=========================================== loading cache ./config.cache checking for gcc... gcc checking whether the C compiler (gcc ) works... yes checking whether the C compiler (gcc ) is a cross-compiler... no checking whether we are using GNU C... yes checking whether gcc accepts -g... yes checking how to run the C preprocessor... gcc -E checking whether make sets ${MAKE}... yes checking for a BSD compatible install... /usr/bin/install -c checking for perl... /usr/bin/perl checking for groff... /usr/bin/groff checking for sqrt in -lm... yes checking for acos in -lm... yes checking for gdImageGif in -lgd... no checking for gdImagePng in -lgd... no checking for gd.h... yes ** The GD library is required for rateup to compile. Get it from http://www.boutell.com, compile it and use either --with-gd-lib=DIR and --with-gd-inc=DIR to specify its location. You might also have to use --with-z-inc, --with-z-lib and --with-png-inc, --with-png-lib for gd versions 1.6 and higher. Check config.log for more information on the problem. If your system has libgd installed, you probably mis the gd.h header file. Consider following the instructions in doc/unix-guide.txt =========================================== 我確定有裝gd及gd-devel 兩rpm,不知還缺啥呢??? 昨晚用家裡機器也架一遍,過程蠻順利的(這台為完整安裝),圖也秀出來,只是介面抓錯了,尚研究中... | |
進階會員 | 引用:
Target[192.168.0.1_2]: 2:[email protected]: MaxBytes[192.168.0.1_2]: 1250000 Title[192.168.0.1_2]: Traffic Analysis for 2 -- Win-2000 PageTop[192.168.0.1_2]: Traffic Analysis for 2 -- Win-2000# ===================================================================== # Target[192.168.0.2_2]: 1:[email protected]: MaxBytes[192.168.0.2_2]: 1250000 Title[192.168.0.2_2]: Traffic Analysis for 1 --FreeBSD PageTop[192.168.0.2_2]: Traffic Analysis for 2 -- FreeBSD存檔..再用indexmaker作一個index.html 再用perl mrtg my.cfg 一直跑...看出來了嗎..? Good Luck !!! | |
進階會員 | 引用:
再試試... Good Luck !!! | |
進階會員 | 引用:
瀏覽器畫面更新時間 --->請修改index.html 將300改成60 再試試... Good Luck !!! | |
進階會員 | 引用:
要不要將錯誤訊息貼上來看看呢?? | |
進階會員 | 引用:
Target[two_nic_plus]id1:community1@ip1 + oid2:community2@ip2 再試試!! Good Luck !!! | |
|
類似的主題 | ||||
主題 | 主題作者 | 討論版 | 回覆 | 最後發表 |
MRTG 裝不起來 | wbc319 | -- FreeBSD & Linux 討 論 版 | 3 | 2006-12-08 10:43 AM |
about Mrtg for win2k | magiclee | -- 網 路 技 術 版 | 3 | 2003-04-07 11:20 PM |
MRTG | celong | -- 網 路 技 術 版 | 0 | 2002-04-19 01:59 PM |
MRTG | hanster | -- 網 路 技 術 版 | 1 | 2001-06-08 12:58 AM |
MRTG 有誰會裝呀? | chengmou | ---- ADSL 軟 硬 體 技 術 | 1 | 2001-06-04 10:02 AM |
XML | RSS 2.0 | RSS |
本論壇所有文章僅代表留言者個人意見,並不代表本站之立場,討論區以「即時留言」方式運作,故無法完全監察所有即時留言,若您發現文章可能有異議,請 email :[email protected] 處理。