2 個附加檔案
【求助】ZyXEL 642M改642R 無法使用Seednet DHCP
請問大家一下,我的ADSL modem是ZyXEL 642M-12 改 642R
Name: ZyXEL_642R
Routing: IP/BRIDGE
ZyNOS S/W Version: V2.50(AJ.3)Feb_2 | 2/2/2001
ADSL Chipset Vendor: Alcatel, Version 3.7.12
Standard: Multi-Mode
之前為了用硬體撥接而改機,但是後來因為IP夠用所以改回手動撥接。
而現在想要改用SEEDNet提供的DHCP服務。但是依照網友說的:
「把Encapsulation改為ENET ENCAP,另外再把IP Address Assignment改為Dynamic應該就可以支援dhcp模式了」
並且連上SEEDNET網站申請DHCP服務後,網路立刻中斷。
最後只好打電話請服務人員關閉DHCP,才能恢復連線
我想請問大家,要怎麼修改設定才能讓我可以使用DHCP呢?
先說聲謝謝嘍
另外,依照網友說的,把Encapsulation改為ENET ENCAP這個部分。我發現我用
ENET模式也可以手動撥號耶@@" 只是會無法顯示下載的流量與封包數。變成附件所示。到底原來的RFC 1483模式和ENET ENCAP模式有什麼不同呢?
回覆: 【求助】ZyXEL 642M改642R 無法使用Seednet DHCP
[QUOTE]
之前為了用硬體撥接而改機,但是後來因為IP夠用所以改回手動撥接。
而現在想要改用SEEDNet提供的DHCP服務。但是依照網友說的:
「把Encapsulation改為ENET ENCAP,另外再把IP Address Assignment改為Dynamic應該就可以支援dhcp模式了」
並且連上SEEDNET網站申請DHCP服務後,網路立刻中斷。
最後只好打電話請服務人員關閉DHCP,才能恢復連線
我想請問大家,要怎麼修改設定才能讓我可以使用DHCP呢?
[/QUOTE]
我的做法事先去申請dhcp的設定,然後再去改atur的設定!
這樣就可以用了!
要注意的是,過一段時間後,atur會發生斷線的現象,重新reboot atur就好了,之後應該就不會在斷線了!
[QUOTE]
另外,依照網友說的,把Encapsulation改為ENET ENCAP這個部分。我發現我用
ENET模式也可以手動撥號耶@@" 只是會無法顯示下載的流量與封包數。變成附件所示。到底原來的RFC 1483模式和ENET ENCAP模式有什麼不同呢? [/B][/QUOTE]
以下是節錄ZyXEL 642說明書中部分的節錄
3.11.4 RFC 1483
RFC 1483 describes two methods for Multiprotocol Encapsulation over ATM Adaptation Layer 5 (AAL5).
The first method allows multiplexing of multiple protocols over a single ATM virtual circuit (LLC-based
multiplexing) and the second method assumes that each protocol is carried over a separate ATM virtual
circuit (VC-based multiplexing). Please refer to the RFC for more detailed information.
3.11.1 ENET ENCAP
The MAC Encapsulated Routing Link Protocol (ENET ENCAP) is only implemented with the IP network
protocol. IP packets are routed between the Ethernet interface and the WAN interface and then formatted so
that they can be understood in a bridged environment i.e., it encapsulates routed Ethernet frames into bridged
ATM cells. ENET ENCAP requires that you specify a gateway IP address in the Ethernet Encapsulation
Gateway field in Menu 4 and in the Rem IP Addr field in Menu 11.1. You can get this information from
your ISP.
3.12.2 Using RFC 1483 Encapsulation
In this case the IP Address Assignment must be static with the same requirements for the IP Address and
ENET ENCAP Gateway fields as stated above.
3.12.3 Using ENET ENCAP Encapsulation
In this case you can have either a static or dynamic IP. For a static IP you must fill in all the IP Address and
ENET ENCAP Gateway fields as supplied by your ISP. However for a dynamic IP, the Prestige acts as a
DHCP client on the WAN port and so the IP Address and ENET ENCAP Gateway fields are not applicable
(N/A) as they are assigned to the Prestige by the DHCP server.
原文post上來,自己慢慢看吧!我也不是非常了解,希望懂得人可以說明一下!:jocky: