[求助] Alcatel T07AW console登入訊息...

請問板上的各位高手：
我之前照著其他大大提供的電路圖，自己做了一組console線，希望可以破解這台ATU-R的無線網路功能...結果遇到一些瓶頸...

出現訊息如下：
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x8018a018
Decompression OK!
Entry at 0x8018a018
Closing network.
Starting program at 0x8018a018
Linux version 2.6.8.1 ([email protected]) (gcc version 3.4.2) #1 Mon No
v 6 10:47:24 CST 2006
Total Flash size: 2048K with 35 sectors
Scratch pad is not used for this flash part.
T07L022-S2 prom init
CPU revision is: 00029107
mpi: No Card is in the PCMCIA slot
Determined physical RAM map:
memory: 007a0000 @ 00000000 (usable)
On node 0 totalpages: 1952
DMA zone: 1952 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 32 (order 5: 256 bytes)
Using 120.000 MHz high precision timer.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 5924k/7808k available (1308k kernel code, 1864k reserved, 199k data, 72k
init, 0k highmem)
Calibrating delay loop... 239.20 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Can't analyze prologue code at 80155c1c
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
bcm963xx_serial driver v2.0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
init started: BusyBox v1.00 (2006.11.06-02:51+0000) multi-call binary
init started: BusyBox v1.00 (2006.11.06-02:51+0000) multi-call binary
Starting pid 30, console /dev/ttyS0: '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
Starting pid 34, console /dev/ttyS0: '/bin/sh'


BusyBox v1.00 (2006.11.06-02:51+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

atmapi: module license 'Proprietary' taints kernel.
blaadd: blaa_detect entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6348B0 Ethernet Network Device v0.3 Nov 6 2006 10:44:39
Config Ethernet Switch Through SPI Slave Select 0
eth0: MAC Address: 00:19:7E:2B:2E:88
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: using main board MAC address base in NVRAM (wombo board)
wl0 MAC Address: 00:19:7E:2B:2E:88
dgasp:reject wl0 registered
wl0: Broadcom BCM4318 802.11 Wireless Controller 3.91.41.0
BcmAdsl_Initialize=0xC0055268, g_pFnNotifyCallback=0xC00694E4
AdslCoreHwReset: AdslOemDataAddr = 0xA07F9220
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
PVC_amount= 1
PVC_amount= 2
Auto-negotiation enabled.
Link is down
Auto-negotiation enabled.
Link is down
Auto-negotiation enabled.
Link is down
Auto-negotiation enabled.
Link is down
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
pvc2684d: Interface "nas_0_33" created sucessfully

pvc2684d: Communicating over ATM 0.0.33, encapsulation: LLC

device nas_0_33 entered promiscuous mode
br0: port 2(nas_0_33) entering learning state
br0: topology change detected, propagating
br0: port 2(nas_0_33) entering forwarding state
pvc2684d: Interface "nas_0_36" created sucessfully

pvc2684d: Communicating over ATM 0.0.36, encapsulation: LLC

device nas_0_36 entered promiscuous mode
br0: port 3(nas_0_36) entering learning state
br0: topology change detected, propagating
br0: port 3(nas_0_36) entering forwarding state
SNMP Disable on WAN and LAN. UDP Socket listen on None
br0: port 1(eth0) entering disabled state
Login: Local Heap: 0x80420E20 - 0x80520E20 (1048576)
Stack Area: 0x80520E20 - 0x80522E20 (8192)
Text (code) segment: 0x80401000 - 0x8041B0B0 (106672)
Boot area (physical): 0x00523000 - 0x00563000
Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : T07L022-S2
Psi size in KB : 24
Number of MAC Addresses (1-32) : 1
Base MAC Address : 00:19:7e:2b:2e:88
Ethernet PHY Type : Internal
Memory size in MB : 8

Login:

===================================================
這時候，我發現鍵盤送出去的字元不聽使喚...
我想key入user...結果出現utre^L^L....
總之，卡在登入畫面了...= =
請問，有人知道這是怎麼回事嗎? 是不是漏了什麼細節呢? thx^^