我的giga P642r韌體更新了卻不能連

**lf138go** · 2001-08-15, 10:34 AM

我的設定是這樣的

Menu 1 - General Setup

System Name= P642r
Location=tTaipei
Contact Person's Name= LF
Route IP= Yes
Route IPX= No
Bridge= No

Menu 3.2 - TCP/IP and DHCP Ethernet Setup

DHCP Setup
DHCP= Server
Client IP Pool Starting Address= 192.168.1.33
Size of Client IP Pool= 32
Primary DNS Server= 203.133.1.8
Secondary DNS Server= 203.133.1.6
Remote DHCP Server= N/A
TCP/IP Setup:
IP Address= 192.168.1.1
IP Subnet Mask= 255.255.255.0
RIP Direction= Both
Version= RIP-1
Multicast= IGMP-v2
IP Policies=
Edit IP Alias= No

Press ENTER to Confirm or ESC to Cancel:

Press Space Bar to Toggle.

Menu 4 - Internet Access Setup

ISP's Name= Giga
Encapsulation= PPPoE .....這改ppp 24-1會顯示up但卻不能上線
Multiplexing= LLC-based
VPI #= 0
VCI #= 33 ..34也有試
Service Name= Any
My Login= username
My Password= ********
Single User Account= Yes
IP Address Assignment= Static
IP Address= My ip
ENET ENCAP Gateway= N/A

Press ENTER to Confirm or ESC to Cancel:

Menu 11.1 - Remote Node Profile

Rem Node Name= Giga Route= IP
Active= Yes Bridge= No
Encapsulation= PPPoE Edit PPP Options= No
Multiplexing= LLC-based Rem IP Addr= 0.0.0.0
Incoming: Edit IP/IPX/Bridge= No
Rem Login=
Rem Password= ********
Outgoing: Session Options:
My Login= username Edit Filter Sets= No
My Password= ******** PPPoE Idle Timeout(sec)= 0
Authen= CHAP/PAP PPPoE Service Name= Any
Schedule Sets= 1, 1, 1, 1

Press ENTER to Confirm or ESC to Cancel:

網路卡設定是..
ip..192.168.1.2
遮罩255.255.255.0
gateway 192.168.1.1
dns 203.133.1.8
203.133.1.6

各位....what can i do 救救我吧!!!

**bx2aa** · 2001-08-15, 11:06 AM

最初由 lf138go
我的設定是這樣的
Menu 3.2 - TCP/IP and DHCP Ethernet Setup
TCP/IP Setup:
IP Address= 192.168.1.1
IP Subnet Mask= 255.255.255.0

Menu 4 - Internet Access Setup
ISP's Name= Giga
Encapsulation= PPPoE .....這改ppp 24-1會顯示up但卻不能上線
Multiplexing= LLC-based
VPI #= 0
VCI #= 33 ..34也有試
Service Name= Any
My Login= username
My Password= ********
Single User Account= Yes
IP Address Assignment= Static
IP Address= My ip
ENET ENCAP Gateway= N/A

網路卡設定是..
ip..192.168.1.2
遮罩255.255.255.0
gateway 192.168.1.1
dns 203.133.1.8
203.133.1.6

各位....what can i do 救救我吧!!!

確定四個燈都亮.

設定不變(ps:VCI 33,34 都試), 然後開機完(ZyXEL ADSL-MODEM) 約三分鐘後進到
24.4.12
Host IP Address= 168.95.1.1
第一次 PING 大約幾秒鐘.

然後再到 24.1 看看有沒有 UP

如果沒有改 VCI 再試一次.

如果 33,34 都一樣,這時就要看 24.3.1 LOG 的訊息是不是 user/pass 不對或是其他問題.

**andyhua** · 2001-08-15, 06:23 PM

你的設定中的:

Menu 4 - Internet Access Setup

Service Name= Any
My Login= username
My Password= ********

應該改成:
My [email protected]
再試試看...

**channing** · 2001-08-15, 07:25 PM

這是之前有人post過的,我也是按照下列的設定就可以了
給你參考!!
===========================================================
(一) 選 1 > Router IP 選 Yes 其他取消
(二) 選 3 -> 2 -> TCP/IP Setup :
TCP/IP Address : 192.168.1.1
IP SubnetMask : 255.255.255.0
其他的用預設就好
(三) 選 4 ->
Encapsulation 設 PPPoE
Service Name 設 Giga
VCI 我是設 33 如果不行改 34
My Login 設帳號
My Password 設密碼
Single User Account 打 Yes
IP Address assignment 選 static
IP Address 打 Giga 給你的 IP
其他的不理
[4] 選 11 -> 1
Active 設 Yes
Authen 設 Chap/PAP
Router 設 IP
Bridge 設 NO
其他的使用預設值..

完成後選 24 -> 1 看第一項的 Status 等等看會不會變 UP , 可以就成功了...

電腦的部分如果你Modem直接連接網卡就將那張網卡設成
IP=192.168.1.2 妳也可以將最後的 2 改成 2~255
遮罩=255.255.255.0
閘道=192.168.1.1

如果妳的 Modem 連接到 Hub 的話確定妳的 ADSL 10M/100M 燈
號有亮一個, 然後可依序將連接到 Hub 的每張網卡依上面設定
去設, 但每台的最後一個值不可相同, 如第一台設 192.168.1.2
第二台就是 192.168.1.3 類推...

[PS]檢查下列情形:

在System Maintenance裡的System Status裡,右下角的 Wan 下面有
Line Statue:up
Upstream Speed=128 kbps
Downstream Speed=768 kbps
=================================================
再順道一提, 我測試的結果, 其他 ISP 撥接式的設法只是將
Service Name 改 Any
IP Address assignment 改選 Dynamic (忘了怎麼拼)
其他的設定步驟大致上相同.. 我成功的改過 Hinet,Seednet 的撥
接式.. 在此提供各位參考...

**lf138go** · 2001-08-15, 11:05 PM

感謝各位大哥不吝指教~~~小弟萬分感激唷!!!
已經ok囉!!

THANKS A LOT

**zesan** · 2001-09-07, 10:57 PM

拜託.........麻煩你再把設定好的東東......post 上來好不好.......
我已照樓上的及樓上上的設...定......,還是沒有好啊!!
我的adsl的燈只亮三個.........adsl的沒亮....
我是用giga... ZYXEL PRESTIGE 642R-51,北部第三-二批

謝謝...

**zesan** · 2001-09-07, 11:09 PM

我的設定檔如下：

Menu 1 - General Setup

System Name= P642r
Location= tTaipei
Contact Person's Name= LF

Route IP= Yes
Route IPX= No
Bridge= No

Menu 3.2 - TCP/IP and DHCP Ethernet Setup

DHCP Setup
DHCP= Server
Client IP Pool Starting Address= 192.168.1.33
Size of Client IP Pool= 32
Primary DNS Server= 203.133.1.8
Secondary DNS Server= 203.133.1.6
Remote DHCP Server= N/A
TCP/IP Setup:
IP Address= 192.168.1.1
IP Subnet Mask= 255.255.255.0
RIP Direction= Both
Version= RIP-1
Multicast= IGMP-v2
IP Policies=
Edit IP Alias= No

Menu 4 - Internet Access Setup

ISP's Name= GIGA
Encapsulation= PPPoE
Multiplexing= LLC-based
VPI #= 0
VCI #= 33
Service Name= Any
My Login= username
My Password= ********
Single User Account= Yes
IP Address Assignment= Static
IP Address= xxx.xxx.xxx.xxx
ENET ENCAP Gateway= N/A

3.Log and Trace
1.View Error Log

59 Sat Jan 1 00:00:01 2000 PP0a INFO LAN promiscuous mode <0>
60 Sat Jan 1 00:00:01 2000 PINI -WARN SNMP TRAP 1: warm start
61 Sat Jan 1 00:00:01 2000 PINI INFO main: init completed
62 Sat Jan 1 00:00:03 2000 PP0f INFO adjtime task pause 1 day
63 Sat Jan 1 00:00:08 2000 PINI INFO SMT Session Begin
Clear Error Log (y/n):

為什麼．．老是在idle.....？？
麻煩各位大大看一下下吧!!

**bx2aa** · 2001-09-08, 01:54 AM

最初由 zesan
我的設定檔如下：
3.Log and Trace
1.View Error Log

59 Sat Jan 1 00:00:01 2000 PP0a INFO LAN promiscuous mode <0>
60 Sat Jan 1 00:00:01 2000 PINI -WARN SNMP TRAP 1: warm start
61 Sat Jan 1 00:00:01 2000 PINI INFO main: init completed
62 Sat Jan 1 00:00:03 2000 PP0f INFO adjtime task pause 1 day
63 Sat Jan 1 00:00:08 2000 PINI INFO SMT Session Begin
Clear Error Log (y/n):

為什麼．．老是在idle.....？？
麻煩各位大大看一下下吧!!

在換另一個 Firmware 試試!
您目前是換哪個版本的 Firmware 呢?
TI Chipset 應該要先確定 Bootbase Version 為 1.06 才能換 AN.1 來用.
Alcatel 如果是用 AJ.3 那還要看是使用哪一個 Firmware 配合哪個版本的 Bootbase
2.02 Bootbase 要配合 642-rn Firmware , 如果是 1.05 用 642rn 就會有 adsl 不亮.
如果換 AJ.4 不好意思我沒有試, 不知道情況, 但應該也一樣.
因為 AJ.4 附的檔案一樣是寫 Bootbase Version 2.02.

**zesan** · 2001-09-09, 10:45 AM

==>成功了.Yh!!
謝謝樓上及樓上上的前輩指導...
原來是我一個設定沒用好,firmware沒有問題.

我的ROUTER是ZyXEL PRESTIGE 600 SERIES 北區第三-二批,Prestige 642R-51
ISP=GIGA ,712/128 個人用戶. 分配到一個固定IP

router設定如下:

Menu 1 - General Setup

System Name= P642r
Location= tTaipei
Contact Person's Name= LF

Route IP= Yes
Route IPX= No
Bridge= No

Menu 3.2 - TCP/IP and DHCP Ethernet Setup

DHCP Setup
DHCP= Server
Client IP Pool Starting Address= 192.168.1.33
Size of Client IP Pool= 32
Primary DNS Server= 203.133.1.8
Secondary DNS Server= 203.133.1.6
Remote DHCP Server= N/A
TCP/IP Setup:
IP Address= 192.168.1.1
IP Subnet Mask= 255.255.255.0
RIP Direction= Both
Version= RIP-2B
Multicast= IGMP-v2
IP Policies=
Edit IP Alias= No

Menu 4 - Internet Access Setup

ISP's Name= GIGA
Encapsulation= PPPoE
Multiplexing= LLC-based
VPI #= 0
VCI #= 33
Service Name= Any
My Login= <<youruserid>>
My Password= <<yourpassword>>
Single User Account= Yes
IP Address Assignment= Dynamic
IP Address= N/A
ENET ENCAP Gateway= N/A

Menu 11.1 - Remote Node Profile

Rem Node Name= GIGA Route= IP
Active= Yes Bridge= No

Encapsulation= PPPoE Edit PPP Options= No
Multiplexing= LLC-based Rem IP Addr= 0.0.0.0
Incoming: Edit IP/IPX/Bridge= No
Rem Login=
Rem Password= ********
Outgoing: Session Options:
My Login= <<youruserid>> Edit Filter Sets= No
My Password= <<yourpassword>> PPPoE Idle Timeout(sec)= 0
Authen= CHAP/PAP PPPoE Service Name= Any
Schedule Sets= 1, 1, 1, 1