【問題】求救!!忘記了IP分享器的密碼...

第 1 頁,共 2 頁 1 2 末頁末頁
顯示結果從第 1 筆 到 10 筆,共計 13 筆
  1. #1
    會員
    註冊日期
    2007-07-18
    所在地區
    ADSL 4m/512
    討論區文章
    29

    【問題】求救!!忘記了IP分享器的密碼...

    我用的是ZYXEL P314,但密碼忘記了,而機身上是沒有reset的按鈕,那有誰可以幫肋我呢??



  2. #2
    缺很大.........
    註冊日期
    2006-07-02
    所在地區
    FTTC
    討論區文章
    614

    回覆: 【問題】求救!!忘記了IP分享器的密碼...

    引用 作者:jaork 瀏覽文章
    我用的是ZYXEL P314,但密碼忘記了,而機身上是沒有reset的按鈕,那有誰可以幫肋我呢??
    通常沒有RESET的按紐的話,大部分都會搭配它自己的CLINET工具軟體去做CONFIG,還是先找找使用手冊吧.

  3. #3
    散人 rushoun 的大頭照
    註冊日期
    2001-07-29
    討論區文章
    5,920

    回覆: 【問題】求救!!忘記了IP分享器的密碼...

    http://www.zyxel.com.tw/web/support_...hp?sqno=328779

    以上是合勤的下載頁面,自己下載後看看吧。
    剛剛看了一下說明,只要把原始的config檔upload回去,就會變成原始密碼1234了。
    此文章於 2007-07-27 12:55 PM 被 rushoun 編輯。
    ========================================
    用智慧處理事情,用慈悲對待他人。(節錄 聖嚴法師與人文對話一書內容)

  4. #4
    會員
    註冊日期
    2007-07-18
    所在地區
    ADSL 4m/512
    討論區文章
    29

    回覆: 【問題】求救!!忘記了IP分享器的密碼...

    引用 作者:rushoun 瀏覽文章
    http://www.zyxel.com.tw/web/support_...hp?sqno=328779

    以上是合勤的下載頁面,自己下載後看看吧。
    剛剛看了一下說明,只要把原始的config檔upload回去,就會變成原始密碼1234了。
    感謝樓上的回復!!
    在p314的使用說明中是有提及到忘記密碼的解決方法,但可惜它是英文,看不懂耶!!內容如下:
    2.6.1 Resetting the Prestige
    If you have forgotten your password or for some reason cannot access the SMT menu you will need to reinstall the configuration file. Uploading the configuration file replaces the current configuration file with
    the default configuration file, you will lose all configurations that you had before and the speed of the console port will be reset to the default of 9600bps with 8 data bit, no parity and 1 stop bit (8n1). The password will be reset to the default of 1234, also.
    Turn off the Prestige and begin a Terminal session with the current console port settings. Turn on the Prestige again. When you see the message "Press Any key to enter Debug Mode within 3 seconds", press any key to
    enter debug mode. You should already have downloaded the correct file from your nearest ZyXEL FTP site.
    See Chapter 9 for more information on how to transfer the configuration file to your Prestige.
    之後我跟它的指示到了Chapter 9 ,但比上段的文字還更看不懂!!
    內容是:
    9.1 Filename Conventions
    The configuration file (often called the romfile or rom-0) contains the factory default settings in the menus such as password, DHCP Setup, TCP/IP Setup etc. It arrives from ZyXEL with a name of P314.ROM or similar. Once you have customized the Prestige's setting, they can be saved back to PC/workstation under a filename of your choosing. Choose something meaningful, e.g., “MyP314.cfg”.
    The ZyNOS firmware file (sometimes referred to as the ras file) is the file that contains the ZyXEL Network
    Operating System firmware and usually is the router model name with a *.bin extension, e.g., P314.bin.
    With serial (XMODEM) transfer, the filenames on the PC are your choice. With many ftp and tftp clients, they are as well as seen next.

    ftp> put P314.bin ras
    This is a sample ftp session showing the transfer of the PC file "P314.bin" to the Prestige.

    ftp> get rom-0 MyP314.cfg
    This is a sample ftp session saving the current configuration to the PC file MyP314.cfg.

    If your [t]ftp client does not allow you have a destination filename different than the source, you will need to
    rename them as the Prestige only recognizes "rom-0" and "ras". Be sure to keep unaltered copies of both files for later use.
    The following table is a summary. Please note that the internal filename refers to the filename on the Prestige and the external filename refers to the filename not on the Prestige, i.e., on your workstation, local network
    or ftp site and so the name (but not the extension) will vary. The AT command is the command you enter
    after you press “Y” when prompted in the SMT menu to go into debug mode. After uploading new firmware
    see the ZyNOS F/W Version field in Menu 24.2.1 (Figure 8-4 Menu 24.2.1 – System Maintenance
    – Information) to check you have uploaded the correct firmware version.

    我還看到這一part(如下),但不知道如何跟著它的步驟去做,連如何進入也不太清楚??

    9.4.2 Uploading Router Configuration File
    The configuration data, system-related data, the error log and the trace log are all stored in the configuration file. Please be aware that uploading the configuration file replaces everything contained within.
    Menu 24.6 replaces the current configuration with your customized configuration you
    backed up previously. Menu 24.7.2 shows you the instructions for uploading the Router Configuration file that replaces the current configuration file with the default configuration file, i.e., P314.rom. You will lose all configurations that you had before
    and the speed of the console port will be reset to the default of 9600 bps with 8 data bit, no parity and 1 stop bit (8n1). You will need to change your serial communications software to the default before you can connect to the Prestige again. The password will
    be reset to the default of 1234, also.
    Follow the procedure below to upload the configuration file:
    Step 1. Enter y at the prompt to go into debug mode.
    Step 2. Enter atlc after the Enter Debug Mode message.
    Step 3. Wait for the Starting XMODEM upload message before activating Xmodem upload on your terminal.
    Step 4. After successful firmware upload, enter atgo to restart the Prestige.


    懇請大大幫忙~~
    此文章於 2007-07-27 02:06 PM 被 jaork 編輯。

  5. #5
    散人 rushoun 的大頭照
    註冊日期
    2001-07-29
    討論區文章
    5,920

    回覆: 【問題】求救!!忘記了IP分享器的密碼...

    說明書有提到,您的電腦要先用RS232連接線接到p314的consol port上,
    電腦要執行類似VT100之類的終端機模擬程式(請記得設定好相關的通訊
    參數9600,n,8,1),然後將p314開機後,VT100應該就可以看到P314
    的相關開機後的資料了。至於FTP部分,我想應該不是你的環境,所以應該
    可以掠過。

    p314開機後3秒內要按下任意鍵後,就可以進入debug mode,之後應該
    就是依照第9章寫的內容,upload firmware回p314中了。

    剛看了一下,您只需要upload config(.ROM檔)檔就可以了,
    不需要upload firmware(.BIN檔)

    這些是說明書說的,不是我講的,沒摸過機器無法測試,只能當參考啦!


    此文章於 2007-07-27 08:33 PM 被 rushoun 編輯。
    ========================================
    用智慧處理事情,用慈悲對待他人。(節錄 聖嚴法師與人文對話一書內容)

  6. #6
    會員
    註冊日期
    2007-07-27
    所在地區
    ADSL 2M/256
    討論區文章
    1

    回覆: 【問題】求救!!忘記了IP分享器的密碼...

    這個情況我建議直接聯絡合勤,請他們教你比較快啦!
    還是直接送修也可以喔!
    Taiwan - 合勤台灣暨香港營運總部
    Tel: +886-2-27399889 免費技術支援:0800500550
    Fax: +886-2-27353220
    Address: 台灣台北市大安區敦化南路2段333號21樓
    Email: [email protected]
    http://www.zyxel.com.tw

  7. #7
    會員
    註冊日期
    2007-07-18
    所在地區
    ADSL 4m/512
    討論區文章
    29

    回覆: 【問題】求救!!忘記了IP分享器的密碼...

    引用 作者:rushoun 瀏覽文章
    說明書有提到,您的電腦要先用RS232連接線接到p314的consol port上,
    電腦要執行類似VT100之類的終端機模擬程式(請記得設定好相關的通訊
    參數9600,n,8,1),然後將p314開機後,VT100應該就可以看到P314
    的相關開機後的資料了。至於FTP部分,我想應該不是你的環境,所以應該
    可以掠過。

    p314開機後3秒內要按下任意鍵後,就可以進入debug mode,之後應該
    就是依照第9章寫的內容,upload firmware回p314中了。

    剛看了一下,您只需要upload config(.ROM檔)檔就可以了,
    不需要upload firmware(.BIN檔)

    這些是說明書說的,不是我講的,沒摸過機器無法測試,只能當參考啦!
    原來是這樣,但我己經將RS232連接線接到p314的consol port上,但電腦好像沒有什麼的變動~~

  8. #8
    會員
    註冊日期
    2007-07-18
    所在地區
    ADSL 4m/512
    討論區文章
    29

    回覆: 【問題】求救!!忘記了IP分享器的密碼...

    我將說明書的重要部分貼上來,希望大大能夠幫助解決我煩了後久的問題,thank!!
    Figure 2-2 Prestige Rear Panel and Connections
    This section outlines how to connect your Prestige 314 to the LAN and the WAN. In the case of connecting a
    cable modem you must connect the coaxial cable from your cable service to the threaded coaxial cable
    connector on the back of the cable modem. Connect a DSL Modem to the DSL Wall Jack. Please also
    see the
    for important safety instructions on making connections to the Prestige.
    Appendices
    Step 1: Connecting the Console Port
    For the initial configuration of your Prestige, you need to use terminal emulator software on a workstation
    and connect it to the Prestige through the console port. Connect the 9-pin end of the console cable to the
    console port of the Prestige and the other end (choice of 9-pin or 25-pin, depending on your computer) end
    to a serial port (COM1, COM2 or other COM port) of your workstation. You can use an extension RS-232cable if the enclosed one is too short. After the initial setup, you can modify the configuration remotely
    through telnet connections.
    Step 2: Connecting the Prestige to the Broadband Modem
    Step 2a.
    Connecting the Prestige to the Cable Modem
    Connect the WAN port on the Prestige to the Ethernet port on the cable modem using the
    cable that came with your cable modem. The Ethernet port on the cable modem is
    sometimes labeled "PC" or "Workstation".
    OR
    Step 2b.
    Connecting the Prestige to the DSL Modem
    Connect the WAN port on the Prestige to the Ethernet port on the DSL modem using the
    cable that came with your DSL modem.
    Step 3: Connecting the Prestige to your LAN
    You can connect up to four computers directly to the Prestige. For each computer, connect the 10/100M LAN
    port on the Prestige to the Network Adapter on the PC using a straight through Ethernet cable (white tag). If
    you have more than four computers, you must use an external hub. Connect LAN port 4 (next to the
    Uplink
    button) on the Prestige to a port on the external hub using a straight through Ethernet cable (white tag) and
    press the button. If you do not press the button (LAN port 4) or use LAN ports 1 to 3 to daisy
    Uplink Uplink
    chain the Prestige to an external hub, then you must use a crossover cable (red tag).
    Step 4: Grounding the Prestige
    F.G.
    If you want to ground the Prestige then connect a grounded wire to the (Frame Ground) of the Prestige.
    Step 5: Connecting the Power Adapter to your Prestige
    POWER
    Connect the power adapter to the port labeled on the rear panel of your Prestige.

    Caution: To prevent damage to the Prestige, first make sure you have the correct AC power
    adapter. Please see the Appendices for AC power adapter specifications for your region.

    2.3 Additional Installation Requirements
    In addition to the contents of your package, there are other hardware and software requirements you need
    before you can install and use your Prestige. These requirements include:
    1. A computer with an Ethernet NIC (Network Interface Card) installed.

    2. A computer equipped with communications software configured to the following parameters:

    VT100 terminal emulation.
    ?
    9600 Baud.
    ?
    No parity, 8 Data bits, 1 Stop bit, Flow Control set to None.
    ?
    3. A cable/DSL modem and an ISP account.

    After the Prestige is properly set up, you can make future changes to the configuration through telnet
    connections.

    2.4 Power Up Your Prestige
    At this point, you should have connected the console port, the LAN port, the WAN port and the power port to
    the appropriate devices or lines. Plug the power adapter into a wall outlet. The Power LED should be on. The
    SYS LED will come on after the system tests are complete. The WAN LED and one of the LAN LEDs come
    on immediately after the SYS LED comes on, if connections have been made to the LAN and WAN ports.
    Initial Screen
    When you power on your Prestige, it performs several internal tests as well as line initialization.
    {Enter}
    After the tests, the Prestige asks you to press
    to continue, as shown.




    Copyright (c) 1994 - 2000 ZyXEL Communications Corp.
    initialize ch =0, ethernet address: 00:a0:c5:41:51:61
    initialize ch =1, ethernet address: 00:a0:c5:41:51:62
    Press ENTER to continue...
    Figure 2-3 Initial Screen





    Entering Password
    The login screen appears after you press [ ], prompting you to enter the password, as shown below.
    Enter
    1234
    For your first login, enter the default password . As you type the password, the screen displays an ( )
    X
    for each character you type.
    Please note that if there is no activity for longer than 5 minutes after you log in, your Prestige will
    automatically log you out and will display a blank screen. If you see a blank screen, press to bring up
    [Enter]
    the login screen again.


    Enter Password : XXXX


    接下是第九章的未完內容:

    9.1.1 Firmware Development
    It is important to upgrade your firmware regularly, especially if there are problems. If you discover an
    unexpected behavior, or bug, see if your problem is mentioned in the release notes. Load it according to
    instructions (e.g., see if the default configuration file is needed also). If the problem still exists, e-mail or call
    tech support.
    9.2 Backup Configuration
    Option 5 from Menu 24 – System Maintenance allows you to backup the current Prestige configuration to
    your workstation. Backup is highly recommended once your Prestige is functioning properly. FTP and TFTP
    are the preferred methods for backing up your current workstation configuration to your computer since FTP
    and TFTP are faster. You can also perform backup and restore using menu 24 through the console port. Any
    serial communications program should work fine; however, you must use XMODEM protocol to perform the
    download/upload and you don’t have to rename the files (see section 9.1).
    Please note that terms “download” and “upload” are relative to the workstation. Download means to transfer
    from the Prestige to the workstation, while upload means from your workstation to the Prestige.
    The following screen is what you see in Menu 24.5 when connected to the Prestige via console port.

    Ready to backup Configuration via Xmodem.
    Do you want to continue (y/n):



    Figure 9-1 Menu 24.5 – System Maintenance – Backup Configuration (Console Port)
    The following screen is what you see in Menu 24.5 when you telnet into the Prestige.



    Menu 24.5 -- System Maintenance - Backup Configuration
    To transfer the configuration file to your workstation, follow the procedure
    below:
    1. Launch the FTP client on your workstation.
    2. Type "open" and the IP address of your router. Then type "root" and
    SMT password as requested.
    3. Locate the 'rom-0' file.
    4. Type 'get rom-0' to back up the current router configuration to
    your workstation.
    For details on FTP commands, please consult the documentation of your FTP
    client program. For details on backup using TFTP (note that you must remain
    in this menu to back up using TFTP), please see your router manual.


    Figure 9-2 Menu 24.5 – System Maintenance – Backup Configuration (Telnet)


    9.3 Restore Configuration
    Menu 24.6 -– System Maintenance – Restore Configuration allows you to restore the configuration via
    the console port.
    FTP and TFTP are the preferred methods for restoring your current workstation configuration to your
    Prestige since FTP and TFTP are faster. Please note that the system reboots automatically after the file
    transfer is complete. The following screen is what you see in Menu 24.5 when connected to the Prestige via
    console port.



    Ready to restore Configuration via Xmodem.
    Do you want to continue (y/n):


    Figure 9-3 Menu 24.6 – System Maintenance – Restore Configuration (Console Port)
    The following screen is what you see in Menu 24.5 when you telnet into the Prestige.


    Menu 24.6 -- System Maintenance - Restore Configuration
    To transfer the firmware and configuration file, follow the procedure
    below:
    1. Launch the FTP client on your workstation.
    2. Type "open" and the IP address of your router. Then type "root" and
    SMT password as requested.
    3. Type "put backupfilename rom-0" where backupfilename is the name of
    your backup configuration file on your workstation and rom-spt is the
    remote file name on the router. This restores the configuration to
    your router.
    4. The system reboots automatically after a successful file transfer.
    For details on FTP commands, please consult the documentation of your FTP
    client program. For details on backup using TFTP (note that you must remain
    in this menu to back up using TFTP), please see your router manual.
    Press ENTER to Exit:



    Figure 9-4 Menu 24.6 – System Maintenance – Restore Configuration (Telnet)


    9.4 Upload Firmware
    Menu 24.7 -– System Maintenance – Upload Firmware allows you to upgrade the firmware and the
    configuration file via the console port. There are two components in the system: the router firmware and the
    configuration file, as shown below.


    Menu 24.7 -- System Maintenance - Upload Firmware
    1. Upload Router Firmware
    2. Upload Router Configuration File
    Enter Menu Selection Number:


    Figure 9-5 Menu 24.7 – System Maintenance – Upload Firmware


    9.4.1 Uploading the Router Firmware
    Menu 24.7.1 shows you the instructions for uploading the router firmware. Follow the procedure below to
    upload the file:
    Step 1.
    Enter at the prompt to go into debug mode.
    y
    Step 2.
    Enter after message.
    atur Enter Debug Mode
    Step 3.
    Wait for the message before activating Xmodem upload on your
    Starting XMODEM upload
    terminal.
    Step 4.
    After successful firmware upload, enter to restart the Prestige.
    atgo


    Menu 24.7.1 - System Maintenance - Upload Router Firmware
    To upload router firmware:
    1. Enter "y" at the prompt below to go into debug mode.
    2. Enter "atur" after "Enter Debug Mode" message.
    3. Wait for "Starting XMODEM upload" message before activating
    Xmodem upload on your terminal.
    4. After successful firmware upload, enter "atgo" to restart the
    router.
    Warning: Proceeding with the upload will erase the current router
    firmware.
    Do You Wish To ProceedY/N)




    Figure 9-6 Menu 24.7.1 – System Maintenance – Upload Router Firmware
    The screen for Menu 24.7.1 when you telnet into the Prestige (see Figure 9-8) is the same except for the
    following additional message.
    “For details on FTP commands, please consult the documentation of your FTP client program. For details on
    uploading router firmware using TFTP (note that you must remain on this menu to upload router firmware
    using TFTP), please see your router manual.”



    9.4.2 Uploading Router Configuration File
    The configuration data, system-related data, the error log and the trace log are all stored in the configuration
    file. Please be aware that uploading the configuration file replaces everything contained within.
    Menu 24.6 replaces the current configuration with your customized configuration you
    backed up previously. Menu 24.7.2 shows you the instructions for uploading the Router
    Configuration file that replaces the current configuration file with the default
    configuration file, i.e., P314.rom. You will lose all configurations that you had before
    and the speed of the console port will be reset to the default of 9600 bps with 8 data
    bit, no parity and 1 stop bit (8n1). You will need to change your serial communications
    software to the default before you can connect to the Prestige again. The password will
    be reset to the default of 1234, also.
    Follow the procedure below to upload the configuration file:
    Step 1.
    Enter at the prompt to go into debug mode.
    y
    Step 2.
    Enter after the message.
    atlc Enter Debug Mode
    Step 3.
    Wait for the message before activating Xmodem upload on you
    Starting XMODEM upload
    terminal.
    Step 4.
    After successful firmware upload, enter to restart the Prestige.
    atgo



    Menu 24.7.2 - System Maintenance - Upload Router Configuration File
    To upload router configuration file:
    1. Enter "y" at the prompt below to go into debug mode.
    2. Enter "atlc" after "Enter Debug Mode" message.
    3. Wait for "Starting XMODEM upload" message before activating
    Xmodem upload on your terminal.
    4. After successful firmware upload, enter "atgo" to restart the
    router.
    Warning:
    1. Proceeding with the upload will erase the current
    configuration file.
    2. The router's console port speed (Menu 24.2.2) may change
    when it is restarted; please adjust your terminal's speed
    accordingly. The password may change (Menu 23), also.
    3. When uploading the DEFAULT configuration file, the console
    port speed will be reset to 9600 bps and the password to
    "1234".
    Do You Wish To ProceedY/N)





    igure 9-7 Menu 24.7.2 – System Maintenance – Upload Router Configuration File
    The screen for Menu 24.7.2 when you telnet into the Prestige (see Figure 9-9) is the same except for the
    following additional message.
    “For details on FTP commands, please consult the documentation of your FTP client program. For details on
    uploading router firmware using TFTP (note that you must remain on this menu to upload router firmware
    using TFTP), please see your router manual.”



    9.5 TFTP File Transfer
    In addition to the direct console port connection, the Prestige supports the up/downloading of the firmware
    and the configuration file using TFTP (Trivial File Transfer Protocol) over LAN. Although TFTP should
    work over WAN as well, it is not recommended.
    To use TFTP, your workstation must have both telnet and TFTP clients. To transfer the firmware and the
    configuration file, follow the next procedure:
    Step 1.
    Use telnet from your workstation to connect to the Prestige and log in. Because TFTP does not
    have any security checks, the Prestige records the IP address of the telnet client and accepts TFTP
    requests only from this address.
    Step 2.
    Put the SMT in command interpreter (CI) mode by entering 8 in Menu 24 – System
    Maintenance.
    Step 3.
    Enter command to disable the SMT timeout, so the TFTP transfer will not be
    sys stdio 0
    interrupted. Enter command to restore the five-minute SMT timeout (default)
    sys stdio 5
    when the file transfer is complete.
    Step 4.
    Launch the TFTP client on your workstation and connect to the Prestige. Set the transfer mode to
    binary before starting data transfer.
    Step 5.
    Use the TFTP client (see the example below) to transfer files between the Prestige and the
    workstation. The file name for the firmware is and for the configuration file, is (rom-
    ras rom-0
    zero, not capital o).



    Note: If you upload the firmware to the Prestige, it will reboot automatically when the
    file transfer is completed (the SYS LED will flash).



    Note that the telnet connection must be active and the SMT in CI mode before and during the TFTP transfer.
    For details on TFTP commands (see following example), please consult the documentation of your TFTP
    client program. For UNIX, use “get” to transfer from the Prestige to the workstation, “put” the other way
    around, and “binary” to set binary transfer mode.


    真的很多,其實還未完的

  9. #9
    會員
    註冊日期
    2007-07-18
    所在地區
    ADSL 4m/512
    討論區文章
    29

    回覆: 【問題】求救!!忘記了IP分享器的密碼...

    我諗現在是不是需要買過另一台的ip分享器呢??究竟現在有沒有辦法拯救這台老舊的東東呢??而新式的分享器和舊式的有什麼的分別呢??如果是買的話那買什麼的型號會好一些呢??我有打算架一個ftp出來的...還有家內的電腦以超過七台了..因此,我也想架出一個完美的管理架構來,望能做到長遠的發展,因為我對這方法的東西不太懂,懇請大大給點見議好嗎??XD
    此文章於 2007-07-28 07:52 PM 被 jaork 編輯。

  10. #10
    先講求不傷電腦,再
    註冊日期
    2007-02-28
    所在地區
    ADSL 2M/512
    討論區文章
    7

    回覆: 【問題】求救!!忘記了IP分享器的密碼...

    其實新的IP分享器,大多都有做RESET的按鈕,這當然不是換新的重點

    家中的電腦有無線上線的需求,倒是可以趁此機會,換台無線的IP分享器
    若有需要QOS的功能,那買台有QOS功能的路由器也不錯
    或是拿家裡其中一台不要用的舊電腦裝BrazilFW當路由器也是不錯的選擇

    最重要的是好好的看一下TCP/IP的書,你會更了解你自己的需求在那裡



類似的主題

  1. 【求助】我忘記了IP分享器之密碼該怎麼辦?
    作者:阿 康 所在討論版:-- HELP ME 電 腦 軟 硬 體 急 救 版
    回覆: 9
    最後發表: 2005-02-11, 04:06 AM
  2. 小弟的IP分享器忘記了密碼...
    作者:52613 所在討論版:-- 網 路 硬 體 版
    回覆: 6
    最後發表: 2004-08-24, 01:55 PM
  3. 【求助】seednet DHCP接了IP分享器的問題!!
    作者:Jimenez 所在討論版:---- ADSL 軟 硬 體 技 術
    回覆: 26
    最後發表: 2004-03-31, 04:55 PM
  4. 【求助】IP分享器的密碼
    作者:leopard 所在討論版:-- 網 路 硬 體 版
    回覆: 3
    最後發表: 2004-02-01, 03:38 AM
  5. MODEM與ip分享器的問題,求救~
    作者:omima 所在討論版:-- Cable Modem 心 得 交 流 版
    回覆: 2
    最後發表: 2002-08-19, 02:44 PM

 

忘記分享器ip

忘記 ip分享器adsl密碼

IP分享氣IP忘記

忘記ip分享器adsl密碼

ip分享器 密碼忘記

分享器 adsl 密碼 忘記

忘記IP分享器

顯示adsl密碼(在ip分享器)

分享器 adsl密碼

忘記adsl密碼 ip分享器

發表文章規則

  • 不可以發表新主題
  • 不可以回覆文章
  • 不可以上傳附加檔案
  • 不可以編輯自己的文章
  •