after
2004-06-01, 03:58 PM
小弟不才,請各位指導
問題:我的route表哪裡設錯了,以致於我的pc2無法透過pc1 tracert到pc3
小弟現有三台pc (w2k pro base) 一台ip share
pc1雙網卡
192.168.5.50 mask 255.255.255.0 default gateway 192.168.5.1
192.168.1.50 mask 255.255.255.0
pc2 192.168.5.200 mask 255.255.255.0 default gateway 192.168.5.1
pc3 192.168.1.100 mask 255.255.255.0
ipshare 192.168.5.1
小弟在pc2上route add 192.168.1.0 mask 255.255.255.0 192.168.5.50後得到下表
IPv4 Route Table
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x10003 ...xx xx xx xx xx xx ...... Marvell Yukon Gigabit Ethernet 10/100/10
00 base-T Adapter, Copper RJ-45
===========================================================================
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface  Metric
          0.0.0.0          0.0.0.0      192.168.5.1    192.168.5.200     20
        127.0.0.0        255.0.0.0        127.0.0.1        127.0.0.1      1
      192.168.1.0    255.255.255.0     192.168.5.50    192.168.5.200     20<--
      192.168.5.0    255.255.255.0    192.168.5.200    192.168.5.200     20<--
    192.168.5.200  255.255.255.255        127.0.0.1        127.0.0.1     20
    192.168.5.255  255.255.255.255    192.168.5.200    192.168.5.200     20
        224.0.0.0        240.0.0.0    192.168.5.200    192.168.5.200     20
  255.255.255.255  255.255.255.255    192.168.5.200    192.168.5.200      1
Default Gateway:       192.168.5.1
===========================================================================
Persistent Routes:
  Network Address          Netmask  Gateway Address  Metric
      192.168.1.0    255.255.255.0     192.168.5.50      20
pc1中之route表如下
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x1000003 ...xx xx xx xx xx xx  ...... 3Com EtherLink PCI
0x1000004 ...xx xx xx xx xx xx ...... SMC EZ Card 10/100 Network Adapter NDI
S5 driver
===========================================================================
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface  Metric
          0.0.0.0          0.0.0.0      192.168.5.1    192.168.5.50       1
        127.0.0.0        255.0.0.0        127.0.0.1       127.0.0.1       1
      192.168.1.0    255.255.255.0     192.168.1.50    192.168.1.50       1<--
     192.168.1.50  255.255.255.255        127.0.0.1       127.0.0.1       1
    192.168.1.255  255.255.255.255     192.168.1.50    192.168.1.50       1
      192.168.5.0    255.255.255.0     192.168.5.50    192.168.5.50       1<--
     192.168.5.50  255.255.255.255        127.0.0.1       127.0.0.1       1
    192.168.5.255  255.255.255.255     192.168.5.50    192.168.5.50       1
        224.0.0.0        224.0.0.0     192.168.1.50    192.168.1.50       1
        224.0.0.0        224.0.0.0     192.168.5.50    192.168.5.50       1
  255.255.255.255  255.255.255.255     192.168.1.50    192.168.1.50       1
Default Gateway:       192.168.5.1
===========================================================================
Persistent Routes:
且ipconfig 中之IP Routing也已打開
Windows 2000 IP Configuration
        Host Name . . . . . . . . . . . . : prac-server
        Primary DNS Suffix  . . . . . . . :
        Node Type . . . . . . . . . . . . : Broadcast
        IP Routing Enabled. . . . . . . . : Yes
        WINS Proxy Enabled. . . . . . . . : No
煩請各位指導,不知是我設定錯誤還是根本上的觀念錯了,感謝
贊助商連結
問題:我的route表哪裡設錯了,以致於我的pc2無法透過pc1 tracert到pc3
小弟現有三台pc (w2k pro base) 一台ip share
pc1雙網卡
192.168.5.50 mask 255.255.255.0 default gateway 192.168.5.1
192.168.1.50 mask 255.255.255.0
pc2 192.168.5.200 mask 255.255.255.0 default gateway 192.168.5.1
pc3 192.168.1.100 mask 255.255.255.0
ipshare 192.168.5.1
小弟在pc2上route add 192.168.1.0 mask 255.255.255.0 192.168.5.50後得到下表
IPv4 Route Table
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x10003 ...xx xx xx xx xx xx ...... Marvell Yukon Gigabit Ethernet 10/100/10
00 base-T Adapter, Copper RJ-45
===========================================================================
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface  Metric
          0.0.0.0          0.0.0.0      192.168.5.1    192.168.5.200     20
        127.0.0.0        255.0.0.0        127.0.0.1        127.0.0.1      1
      192.168.1.0    255.255.255.0     192.168.5.50    192.168.5.200     20<--
      192.168.5.0    255.255.255.0    192.168.5.200    192.168.5.200     20<--
    192.168.5.200  255.255.255.255        127.0.0.1        127.0.0.1     20
    192.168.5.255  255.255.255.255    192.168.5.200    192.168.5.200     20
        224.0.0.0        240.0.0.0    192.168.5.200    192.168.5.200     20
  255.255.255.255  255.255.255.255    192.168.5.200    192.168.5.200      1
Default Gateway:       192.168.5.1
===========================================================================
Persistent Routes:
  Network Address          Netmask  Gateway Address  Metric
      192.168.1.0    255.255.255.0     192.168.5.50      20
pc1中之route表如下
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x1000003 ...xx xx xx xx xx xx  ...... 3Com EtherLink PCI
0x1000004 ...xx xx xx xx xx xx ...... SMC EZ Card 10/100 Network Adapter NDI
S5 driver
===========================================================================
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface  Metric
          0.0.0.0          0.0.0.0      192.168.5.1    192.168.5.50       1
        127.0.0.0        255.0.0.0        127.0.0.1       127.0.0.1       1
      192.168.1.0    255.255.255.0     192.168.1.50    192.168.1.50       1<--
     192.168.1.50  255.255.255.255        127.0.0.1       127.0.0.1       1
    192.168.1.255  255.255.255.255     192.168.1.50    192.168.1.50       1
      192.168.5.0    255.255.255.0     192.168.5.50    192.168.5.50       1<--
     192.168.5.50  255.255.255.255        127.0.0.1       127.0.0.1       1
    192.168.5.255  255.255.255.255     192.168.5.50    192.168.5.50       1
        224.0.0.0        224.0.0.0     192.168.1.50    192.168.1.50       1
        224.0.0.0        224.0.0.0     192.168.5.50    192.168.5.50       1
  255.255.255.255  255.255.255.255     192.168.1.50    192.168.1.50       1
Default Gateway:       192.168.5.1
===========================================================================
Persistent Routes:
且ipconfig 中之IP Routing也已打開
Windows 2000 IP Configuration
        Host Name . . . . . . . . . . . . : prac-server
        Primary DNS Suffix  . . . . . . . :
        Node Type . . . . . . . . . . . . : Broadcast
        IP Routing Enabled. . . . . . . . : Yes
        WINS Proxy Enabled. . . . . . . . : No
煩請各位指導,不知是我設定錯誤還是根本上的觀念錯了,感謝
贊助商連結