France
2001-07-17, 12:27 PM
我已經更新完韌體...畫面如下
Menu 24.2.1 - System Maintenance - Information
Name: Zyxel Prestige 642R-51
Routing: IP/BRIDGE
ZyNOS S/W Version: V2.50(AJ.3)Feb_2 | 2/2/2001
ADSL Chipset Vendor: Alcatel, Version 3.7.12
Standard: Multi-Mode
LAN
Ethernet Address: 00:a0:c5:16:39:ae
IP Address: 192.168.1.1
IP Mask: 255.255.255.0
DHCP: Server
-------------------------------------------------------------------------------
問題就是...看別人教學的設定..就是不能硬撥~~好奇怪~~大家可以把自己設定的選項..po出來嗎??謝謝各位...~~~一動設定..raspppoe一定找不到主機..我"軟撥"的設定如下:
Menu 1 - General Setup
System Name= Zyxel Prestige 642R-51
Location= Taipei
Contact Person's Name=
Route IP= Yes
Route IPX= No
Bridge= Yes
Menu 4 - Internet Access Setup
ISP's Name= hinet
Encapsulation= RFC 1483
Multiplexing= LLC-based
VPI #= 0
VCI #= 34
Service Name= N/A
My Login= N/A
My Password= N/A
Single User Account= Yes
IP Address Assignment= Static
IP Address= 0.0.0.0
ENET ENCAP Gateway= N/A
Menu 11.1 - Remote Node Profile
Rem Node Name= hinet Route= IP
Active= Yes Bridge= Yes
Encapsulation= RFC 1483 Edit PPP Options= N/A
Multiplexing= LLC-based Rem IP Addr= 0.0.0.0
Incoming: Edit IP/IPX/Bridge= No
Rem Login= N/A
Rem Password= N/A
Outgoing: Session Options:
My Login= N/A Edit Filter Sets= No
My Password= N/A PPPoE Idle Timeout(sec)= N/A
Authen= N/A PPPoE Service Name= N/A
Schedule Sets= N/A
-------------------------------------------------------------------------------還有改完硬撥後~~一開機就是直接上網嗎??還是必須要如何才能啟動硬撥??...
Menu 24.1 - System Maintenance - Status
Node-Lnk Status TxPkts RxPkts Errors Tx B/s Rx B/s Up Time
1-1483 Up 3687 3159 0 0 0 0:18:57
照別人的硬撥設定改...Status就是會顯示Idle....所以請大家幫幫忙囉~~~之前的設定都
試過..搞了一個晚上..真的不行~~才需要大家的協助~~謝謝囉~~~
贊助商連結
Menu 24.2.1 - System Maintenance - Information
Name: Zyxel Prestige 642R-51
Routing: IP/BRIDGE
ZyNOS S/W Version: V2.50(AJ.3)Feb_2 | 2/2/2001
ADSL Chipset Vendor: Alcatel, Version 3.7.12
Standard: Multi-Mode
LAN
Ethernet Address: 00:a0:c5:16:39:ae
IP Address: 192.168.1.1
IP Mask: 255.255.255.0
DHCP: Server
-------------------------------------------------------------------------------
問題就是...看別人教學的設定..就是不能硬撥~~好奇怪~~大家可以把自己設定的選項..po出來嗎??謝謝各位...~~~一動設定..raspppoe一定找不到主機..我"軟撥"的設定如下:
Menu 1 - General Setup
System Name= Zyxel Prestige 642R-51
Location= Taipei
Contact Person's Name=
Route IP= Yes
Route IPX= No
Bridge= Yes
Menu 4 - Internet Access Setup
ISP's Name= hinet
Encapsulation= RFC 1483
Multiplexing= LLC-based
VPI #= 0
VCI #= 34
Service Name= N/A
My Login= N/A
My Password= N/A
Single User Account= Yes
IP Address Assignment= Static
IP Address= 0.0.0.0
ENET ENCAP Gateway= N/A
Menu 11.1 - Remote Node Profile
Rem Node Name= hinet Route= IP
Active= Yes Bridge= Yes
Encapsulation= RFC 1483 Edit PPP Options= N/A
Multiplexing= LLC-based Rem IP Addr= 0.0.0.0
Incoming: Edit IP/IPX/Bridge= No
Rem Login= N/A
Rem Password= N/A
Outgoing: Session Options:
My Login= N/A Edit Filter Sets= No
My Password= N/A PPPoE Idle Timeout(sec)= N/A
Authen= N/A PPPoE Service Name= N/A
Schedule Sets= N/A
-------------------------------------------------------------------------------還有改完硬撥後~~一開機就是直接上網嗎??還是必須要如何才能啟動硬撥??...
Menu 24.1 - System Maintenance - Status
Node-Lnk Status TxPkts RxPkts Errors Tx B/s Rx B/s Up Time
1-1483 Up 3687 3159 0 0 0 0:18:57
照別人的硬撥設定改...Status就是會顯示Idle....所以請大家幫幫忙囉~~~之前的設定都
試過..搞了一個晚上..真的不行~~才需要大家的協助~~謝謝囉~~~
贊助商連結