最初由 Net surfer 發表
我的2000也常常出現這些類似畫面...
發生這些錯誤的前兆是硬碟會開始嘎拉嘎拉的叫...
讀取燈一直亮著...
然後就掛了...
暖開機沒有用說...
會出現"Hard Disk Diagnosis Fail"的錯誤訊息... 掛在那裡...

我猜想說是不是讀到壞軌的地方了...
因為這顆硬碟也差不多了... @@

之後我改灌到G槽... (之前灌在C槽)
發生這種錯誤的次數就減少很多了...
不過...
在C槽存取檔案時還是常常會發生這樣的錯誤...

所以我的結論是...
=> 大概是C槽被我操爛掉了吧... ><" (好在還有D,E,F,G,H 可以用:jump2: )

參考看看...

沒錯!我跟你一樣前兆是硬碟會開始嘎拉嘎拉的叫,我當初沒想太多,我想硬碟早晚也會變這
樣,而且硬碟的溫度比之前高出很多......

可是這顆S60G 我才買三個月,比我新電腦還要晚很早才買...
我那顆S20G用了四年了,到現在除了比較吵都很正常>_____<

贊助商連結

最初由 Schnaufer 發表
Stop Error 0x0000000A

Descriptive text: IRQL_NOT_LESS_OR_EQUAL

Usual cause:

　　Drivers are using improper memory addresses.


　　To troubleshoot Stop error 0x0000000A on an existing installation
If you are unable to log on, restart your computer. When the list of available operating systems appears, press F8. On the Windows 2000 Advanced Options Menu screen, select Last Known Good Configuration, and then press ENTER.
Verify that any new hardware or software is properly installed. If this is a new installation, contact your hardware or software manufacturer for any Windows 2000 updates or drivers you might need.
Check the Microsoft Hardware Compatibility List to verify that all your hardware and drivers are compatible with Windows 2000.
To see the most recent version of the HCL, visit the Microsoft Web site: http://www.microsoft.com/hcl/
Run any system diagnostic software supplied by your computer manufacturer, especially the memory check.
Disable or remove any newly installed hardware (RAM, adapters, hard disks, modems, and so on), drivers, or software.
Verify that your hardware devices drivers and your system BIOS are the latest available versions.
Your hardware manufacturers can help you determine whether you have the latest versions or help you obtain them.
Disable BIOS memory options such as caching or shadowing.
If you need assistance, contact your hardware manufacturer.

Explanation:

　　This is a Windows 2000 Executive character-mode STOP message. It indicates an attempt was made to touch pageable memory at a process IRQL (interrupt request level) that is too high. This is usually caused by drivers using incorrect addresses. The fourth parameter in the message parameter list is the memory address at which the fault happened. The second parameter shows the IRQL. If the IRQL was not equal to 2, then the interrupt most likely came from a driver. Compare the memory address in the fourth parameter with the base addresses of the drivers in the driver table on the STOP screen to find the driver that is the problem. Note that the third parameter encodes read/write access (0 = read, 1= write).

User Action:

　　If this is the first time you have booted after installing new hardware, remove the hardware and boot again. Check the Microsoft Hardware Compatibility List to verify that the hardware and its drivers are compatible with Windows 2000. For information about the hardware, contact the supplier. If you are installing Windows 2000 for the first time, check the Windows 2000 system requirements, including the amount of RAM and disk space required to load the operating system. Also, check the Hardware Compatibility List to verify that the system can run Windows 2000. If Windows 2000 is loaded and no new hardware has been installed, reboot with recovery options set to create a dump file. If the message continues to appear, select the Last Known Good option when you reboot. If there is no Last Known Good configuration, try using the Emergency Repair Disk. If you do not have an Emergency Repair Disk, contact your technical support group.


　　很可能是在讀取記憶體時的問題，去找個記憶體測試軟體測測看吧！創見可以終身免費更換。讀取的驅動程式及發生問題的記憶體位址都顯示在訊息上。

　　附帶說明一下，通常 0x0000000A 的錯誤訊息與 Ntorkrnl.exe 驅動程式同時發生問題比較常出現在 NT 4.0 的作業系統，另外，0x0000000A 的錯誤訊息也常常出現在 SMP（雙 CPU）的電腦上。

記憶體測試軟體,請問有軟體的名稱嗎???

我知道創見有終身免費更換,可是我怕這樣他不給我換.....
還是要弄壞他才給我換:P

最初由 Schnaufer 發表

　　很可能是在讀取記憶體時的問題，去找個記憶體測試軟體測測看吧！創見可以終身免費更換。讀取的驅動程式及發生問題的記憶體位址都顯示在訊息上。

　　附帶說明一下，通常 0x0000000A 的錯誤訊息與 Ntorkrnl.exe 驅動程式同時發生問題比較常出現在 NT 4.0 的作業系統，另外，0x0000000A 的錯誤訊息也常常出現在 SMP（雙
CPU）的電腦上。 [/B]

可是我有的時候跑一整個晚上又都沒有問題
怎麼會這樣呢
而且我用的是XP 和 ME ,
測試軟體哪邊有呢
拜託你了

最初由 KingHsuan 發表



而且我用的是XP 和 ME ,
測試軟體哪邊有呢
拜託你了 DocMemory (http://downloads-zdnet.com.com/3000-2094-10038801.html)請善用GOOGLE.

換motherboard看看
應該是motherboard的問題

連版子都換？？哪這ㄇ多錢...

什麼都換,算了吧!!不敢領教...
我想可能電腦太累了吧!因為我有一星期都沒關機
我讓電腦休息一天,在用norton將全部重組,目前情形很良好都沒有當機
*^_^*

最初由 ericlien 發表
DocMemory (http://downloads-zdnet.com.com/3000-2094-10038801.html)請善用GOOGLE.

我有把ram拿到我同學的電腦上面去測試
結果用 Norton 測試出來的結果是有位址發生錯誤
可是如果不是把兩條ram一起插上去一起測試的話
(就是一次插一條ram來測試....就都沒有問題了)
怎麼會這樣呢 ?http://home.pchome.com.tw/todo/kinghsuan/ram.jpg

最初由 KingHsuan 發表


我有把ram拿到我同學的電腦上面去測試
結果用 Norton 測試出來的結果是有位址發生錯誤
可是如果不是把兩條ram一起插上去一起測試的話
(就是一次插一條ram來測試....就都沒有問題了)
怎麼會這樣呢 ?http://home.pchome.com.tw/todo/kinghsuan/ram.jpg

Norton本身測試超過256mb就會有問題,新版Norton就不再附這項功能

最初由 jamesex 發表


Norton本身測試超過256mb就會有問題,新版Norton就不再附這項功能

原來如此...
而我日前去創見問的結果是
茂矽的晶片 和 MSI 的主機板會相衝...
等我去把RAM換掉在試試看....
謝謝...