* 轉貼下列文章請註明作者與出處 *
Alcatel T07AW 之 Wireless 功能開啟程序 (hungwen@PCZone):
需以 Console 連接線 (製作方式與
Alcatel T07L011 相同, 但是 RX、TX 與 Alcatel T07L011 相反, 建議用 DIN-PS2 鍵盤轉換線來改裝) 與 Alcatel T07AW 連接, 使用 Hyper Terminal 來登入 Alcatel T07AW (115200,N,8,1) 進行下列操作.
Login: cht
Password:
Main Menu
1. ADSL Link State
2. LAN
3. WAN
4. DNS Server
5. Route Setup
6. NAT
7. Firewall
8. Quality Of Service
9. Management
10. Passwords
11. Reset to Default
12. Save and Reboot
13. Exit
14. Wireless
-> 14
Wireless Menu
1. Basic
2. Security
3. Save and Reboot
4. Exit
/Wireless -> 1
Wireless Basic Menu
1. SSID
2. Channel
3. Radio Power(mW)
4. Multicast Rate
5. Basic Rate
6. Exit
/Wireless/Basic -> 7
Wireless is Disabled
Enable/Disable Wireless? Confirm [1-enable,2-disable] ==> 1
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
br0: port 3(wl0) entering disabled state
Setting country code "TW"
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
channel selected 6
wl0: Device or resource busy
wme Set WME (Wireless Multimedia Extensions) mode (0=off, 1=on)
channel selected 6
br0: port 3(wl0) entering disabled state
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
br0: port 3(wl0) entering disabled state
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
device wl0 is already a member of a bridge; can't enslave it to bridge br0.
******** You must reboot after changing any setting. ********
Hit <enter> to continue
Wireless Basic Menu
1. SSID
2. Channel
3. Radio Power(mW)
4. Multicast Rate
5. Basic Rate
6. Exit
/Wireless/Basic -> 6
Wireless Menu
1. Basic
2. Security
3. Save and Reboot
4. Exit
/Wireless -> 3
Save current configuration and reboot? Confirm [1-yes,2-no] ==> 1
PID Uid VmSize Stat Command
1 cht 212 S init
2 cht SWN [ksoftirqd/0]
3 cht SW< [events/0]
4 cht SW< [khelper]
5 cht SW< [kblockd/0]
17 cht SW [pdflush]
18 cht SW [pdflush]
19 cht SW [kswapd0]
20 cht SW< [aio/0]
25 cht SW [mtdblockd]
34 cht 268 S -sh
58 cht 832 S cfm
102 cht 180 S pvc2684d
221 cht 752 S telnetd
222 cht 776 S sshd
223 cht 788 S snmp
224 cht 876 S httpd
389 cht 248 S sh -c ps > /var/pslist
390 cht 236 R ps
Number of processes: 19
12:01am up 1 min,
load average: 1 min:0.25, 5 min:0.08, 15 min:0.02
total used free shared buffers
Mem: 6016 5500 516 0 332
Swap: 0 0 0
Total: 6016 5500 516
kill snmp process...
iptables v1.2.11: can't initialize iptables table `nat': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
Remaining modules:
wl 360064 0 - Live 0xc00e9000
bcm_enet 18608 0 - Live 0xc002b000
bcmprocfs 12288 0 - Live 0xc000f000
adsldd 119472 0 - Live 0xc0054000
blaadd 5904 0 - Live 0xc000c000
atmapi 48144 2 adsldd,blaadd, Live 0xc001e000
Memory info:
Number of processes: 18
12:01am up 1 min,
load average: 1 min:0.25, 5 min:0.08, 15 min:0.02
total used free shared buffers
Mem: 6016 5588 428 0 360
Swap: 0 0 0
Total: 6016 5588 428
The system shell is being reset. Please wait...
在 Wireless 功能開啟後, 再以 Web 連線方式登入 Alcatel T07AW, 就可以看見多出一個 "Wireless" 設定選項...
註1:進入 CFE (Boot Loader) 之後, 請小心使用這兩個指令:e 與 i, 這兩個指令功能並不等同於 "Restore to Default", 以免造成無法挽救之結果.
CFE> help
Available commands:
w Write the whole image start from beginning of the flash
e Erase [n]vram or [a]ll flash except bootrom
r Run program from flash image or from host depend on [f/h] flag
p Print boot line and board parameter info
c Change booline parameters
f Write image to the flash
i Erase persistent storage data
b Change board parameters
reset Reset the board
flashimage Flashes a compressed image after the bootloader.
help Obtain help for CFE commands
For more information about a command, enter 'help command-name'
*** command status = 0
CFE>
註2:由於 Alcatel T07AW 採用 Broadcom BCM6348 晶片, 因此也適用
這篇文章之操作程序.