【問題】求救!!忘記了IP分享器的密碼...


頁 : [1] 2

jaork
2007-07-27, 02:19 AM
我用的是ZYXEL P314,但密碼忘記了,而機身上是沒有reset的按鈕,那有誰可以幫肋我呢??:(

RouterOS
2007-07-27, 08:54 AM
我用的是ZYXEL P314,但密碼忘記了,而機身上是沒有reset的按鈕,那有誰可以幫肋我呢??:(

通常沒有RESET的按紐的話,大部分都會搭配它自己的CLINET工具軟體去做CONFIG,還是先找找使用手冊吧.

rushoun
2007-07-27, 12:34 PM
http://www.zyxel.com.tw/web/support_download_detail.php?sqno=328779

以上是合勤的下載頁面,自己下載後看看吧。
剛剛看了一下說明,只要把原始的config檔upload回去,就會變成原始密碼1234了。

jaork
2007-07-27, 02:00 PM
http://www.zyxel.com.tw/web/support_download_detail.php?sqno=328779

以上是合勤的下載頁面,自己下載後看看吧。
剛剛看了一下說明,只要把原始的config檔upload回去,就會變成原始密碼1234了。

感謝樓上的回復!!
在p314的使用說明中是有提及到忘記密碼的解決方法,但可惜它是英文,看不懂耶!!內容如下:
2.6.1 Resetting the Prestige
If you have forgotten your password or for some reason cannot access the SMT menu you will need to reinstall the configuration file. Uploading the configuration file replaces the current configuration file with
the default configuration file, you will lose all configurations that you had before and the speed of the console port will be reset to the default of 9600bps with 8 data bit, no parity and 1 stop bit (8n1). The password will be reset to the default of 1234, also.
Turn off the Prestige and begin a Terminal session with the current console port settings. Turn on the Prestige again. When you see the message "Press Any key to enter Debug Mode within 3 seconds", press any key to
enter debug mode. You should already have downloaded the correct file from your nearest ZyXEL FTP site.
See Chapter 9 for more information on how to transfer the configuration file to your Prestige.
之後我跟它的指示到了Chapter 9 ,但比上段的文字還更看不懂!!:cry:
內容是:
9.1 Filename Conventions
The configuration file (often called the romfile or rom-0) contains the factory default settings in the menus such as password, DHCP Setup, TCP/IP Setup etc. It arrives from ZyXEL with a name of P314.ROM or similar. Once you have customized the Prestige's setting, they can be saved back to PC/workstation under a filename of your choosing. Choose something meaningful, e.g., “MyP314.cfg”.
The ZyNOS firmware file (sometimes referred to as the ras file) is the file that contains the ZyXEL Network
Operating System firmware and usually is the router model name with a *.bin extension, e.g., P314.bin.
With serial (XMODEM) transfer, the filenames on the PC are your choice. With many ftp and tftp clients, they are as well as seen next.

ftp> put P314.bin ras
This is a sample ftp session showing the transfer of the PC file "P314.bin" to the Prestige.

ftp> get rom-0 MyP314.cfg
This is a sample ftp session saving the current configuration to the PC file MyP314.cfg.

If your [t]ftp client does not allow you have a destination filename different than the source, you will need to
rename them as the Prestige only recognizes "rom-0" and "ras". Be sure to keep unaltered copies of both files for later use.
The following table is a summary. Please note that the internal filename refers to the filename on the Prestige and the external filename refers to the filename not on the Prestige, i.e., on your workstation, local network
or ftp site and so the name (but not the extension) will vary. The AT command is the command you enter
after you press “Y” when prompted in the SMT menu to go into debug mode. After uploading new firmware
see the ZyNOS F/W Version field in Menu 24.2.1 (Figure 8-4 Menu 24.2.1 – System Maintenance
– Information) to check you have uploaded the correct firmware version.

我還看到這一part(如下),但不知道如何跟著它的步驟去做,連如何進入也不太清楚??

9.4.2 Uploading Router Configuration File
The configuration data, system-related data, the error log and the trace log are all stored in the configuration file. Please be aware that uploading the configuration file replaces everything contained within.
Menu 24.6 replaces the current configuration with your customized configuration you
backed up previously. Menu 24.7.2 shows you the instructions for uploading the Router Configuration file that replaces the current configuration file with the default configuration file, i.e., P314.rom. You will lose all configurations that you had before
and the speed of the console port will be reset to the default of 9600 bps with 8 data bit, no parity and 1 stop bit (8n1). You will need to change your serial communications software to the default before you can connect to the Prestige again. The password will
be reset to the default of 1234, also.
Follow the procedure below to upload the configuration file:
Step 1. Enter y at the prompt to go into debug mode.
Step 2. Enter atlc after the Enter Debug Mode message.
Step 3. Wait for the Starting XMODEM upload message before activating Xmodem upload on your terminal.
Step 4. After successful firmware upload, enter atgo to restart the Prestige.


懇請大大幫忙~~:lovely:

rushoun
2007-07-27, 08:26 PM
說明書有提到,您的電腦要先用RS232連接線接到p314的consol port上,
電腦要執行類似VT100之類的終端機模擬程式(請記得設定好相關的通訊
參數9600,n,8,1),然後將p314開機後,VT100應該就可以看到P314
的相關開機後的資料了。至於FTP部分,我想應該不是你的環境,所以應該
可以掠過。

p314開機後3秒內要按下任意鍵後,就可以進入debug mode,之後應該
就是依照第9章寫的內容,upload firmware回p314中了。

剛看了一下,您只需要upload config(.ROM檔)檔就可以了,
不需要upload firmware(.BIN檔)

這些是說明書說的,不是我講的,沒摸過機器無法測試,只能當參考啦!

walterdiablo
2007-07-27, 08:32 PM
這個情況我建議直接聯絡合勤,請他們教你比較快啦!
還是直接送修也可以喔!
Taiwan - 合勤台灣暨香港營運總部
Tel: +886-2-27399889 免費技術支援:0800500550
Fax: +886-2-27353220
Address: 台灣台北市大安區敦化南路2段333號21樓
Email: ZyTPE@zyxel.com.tw
http://www.zyxel.com.tw

jaork
2007-07-27, 11:58 PM
說明書有提到,您的電腦要先用RS232連接線接到p314的consol port上,
電腦要執行類似VT100之類的終端機模擬程式(請記得設定好相關的通訊
參數9600,n,8,1),然後將p314開機後,VT100應該就可以看到P314
的相關開機後的資料了。至於FTP部分,我想應該不是你的環境,所以應該
可以掠過。

p314開機後3秒內要按下任意鍵後,就可以進入debug mode,之後應該
就是依照第9章寫的內容,upload firmware回p314中了。

剛看了一下,您只需要upload config(.ROM檔)檔就可以了,
不需要upload firmware(.BIN檔)

這些是說明書說的,不是我講的,沒摸過機器無法測試,只能當參考啦!

原來是這樣,但我己經將RS232連接線接到p314的consol port上,但電腦好像沒有什麼的變動~~:(

jaork
2007-07-28, 12:28 AM
我將說明書的重要部分貼上來,希望大大能夠幫助解決我煩了後久的問題,thank!!
Figure 2-2 Prestige Rear Panel and Connections
This section outlines how to connect your Prestige 314 to the LAN and the WAN. In the case of connecting a
cable modem you must connect the coaxial cable from your cable service to the threaded coaxial cable
connector on the back of the cable modem. Connect a DSL Modem to the DSL Wall Jack. Please also
see the
for important safety instructions on making connections to the Prestige.
Appendices
Step 1: Connecting the Console Port
For the initial configuration of your Prestige, you need to use terminal emulator software on a workstation
and connect it to the Prestige through the console port. Connect the 9-pin end of the console cable to the
console port of the Prestige and the other end (choice of 9-pin or 25-pin, depending on your computer) end
to a serial port (COM1, COM2 or other COM port) of your workstation. You can use an extension RS-232cable if the enclosed one is too short. After the initial setup, you can modify the configuration remotely
through telnet connections.
Step 2: Connecting the Prestige to the Broadband Modem
Step 2a.
Connecting the Prestige to the Cable Modem
Connect the WAN port on the Prestige to the Ethernet port on the cable modem using the
cable that came with your cable modem. The Ethernet port on the cable modem is
sometimes labeled "PC" or "Workstation".
OR
Step 2b.
Connecting the Prestige to the DSL Modem
Connect the WAN port on the Prestige to the Ethernet port on the DSL modem using the
cable that came with your DSL modem.
Step 3: Connecting the Prestige to your LAN
You can connect up to four computers directly to the Prestige. For each computer, connect the 10/100M LAN
port on the Prestige to the Network Adapter on the PC using a straight through Ethernet cable (white tag). If
you have more than four computers, you must use an external hub. Connect LAN port 4 (next to the
Uplink
button) on the Prestige to a port on the external hub using a straight through Ethernet cable (white tag) and
press the button. If you do not press the button (LAN port 4) or use LAN ports 1 to 3 to daisy
Uplink Uplink
chain the Prestige to an external hub, then you must use a crossover cable (red tag).
Step 4: Grounding the Prestige
F.G.
If you want to ground the Prestige then connect a grounded wire to the (Frame Ground) of the Prestige.
Step 5: Connecting the Power Adapter to your Prestige
POWER
Connect the power adapter to the port labeled on the rear panel of your Prestige.

Caution: To prevent damage to the Prestige, first make sure you have the correct AC power
adapter. Please see the Appendices for AC power adapter specifications for your region.

2.3 Additional Installation Requirements
In addition to the contents of your package, there are other hardware and software requirements you need
before you can install and use your Prestige. These requirements include:
1. A computer with an Ethernet NIC (Network Interface Card) installed.

2. A computer equipped with communications software configured to the following parameters:

VT100 terminal emulation.
?
9600 Baud.
?
No parity, 8 Data bits, 1 Stop bit, Flow Control set to None.
?
3. A cable/DSL modem and an ISP account.

After the Prestige is properly set up, you can make future changes to the configuration through telnet
connections.

2.4 Power Up Your Prestige
At this point, you should have connected the console port, the LAN port, the WAN port and the power port to
the appropriate devices or lines. Plug the power adapter into a wall outlet. The Power LED should be on. The
SYS LED will come on after the system tests are complete. The WAN LED and one of the LAN LEDs come
on immediately after the SYS LED comes on, if connections have been made to the LAN and WAN ports.
Initial Screen
When you power on your Prestige, it performs several internal tests as well as line initialization.
{Enter}
After the tests, the Prestige asks you to press
to continue, as shown.




Copyright (c) 1994 - 2000 ZyXEL Communications Corp.
initialize ch =0, ethernet address: 00:a0:c5:41:51:61
initialize ch =1, ethernet address: 00:a0:c5:41:51:62
Press ENTER to continue...
Figure 2-3 Initial Screen





Entering Password
The login screen appears after you press [ ], prompting you to enter the password, as shown below.
Enter
1234
For your first login, enter the default password . As you type the password, the screen displays an ( )
X
for each character you type.
Please note that if there is no activity for longer than 5 minutes after you log in, your Prestige will
automatically log you out and will display a blank screen. If you see a blank screen, press to bring up
[Enter]
the login screen again.


Enter Password : XXXX


接下是第九章的未完內容:

9.1.1 Firmware Development
It is important to upgrade your firmware regularly, especially if there are problems. If you discover an
unexpected behavior, or bug, see if your problem is mentioned in the release notes. Load it according to
instructions (e.g., see if the default configuration file is needed also). If the problem still exists, e-mail or call
tech support.
9.2 Backup Configuration
Option 5 from Menu 24 – System Maintenance allows you to backup the current Prestige configuration to
your workstation. Backup is highly recommended once your Prestige is functioning properly. FTP and TFTP
are the preferred methods for backing up your current workstation configuration to your computer since FTP
and TFTP are faster. You can also perform backup and restore using menu 24 through the console port. Any
serial communications program should work fine; however, you must use XMODEM protocol to perform the
download/upload and you don’t have to rename the files (see section 9.1).
Please note that terms “download” and “upload” are relative to the workstation. Download means to transfer
from the Prestige to the workstation, while upload means from your workstation to the Prestige.
The following screen is what you see in Menu 24.5 when connected to the Prestige via console port.

Ready to backup Configuration via Xmodem.
Do you want to continue (y/n):



Figure 9-1 Menu 24.5 – System Maintenance – Backup Configuration (Console Port)
The following screen is what you see in Menu 24.5 when you telnet into the Prestige.



Menu 24.5 -- System Maintenance - Backup Configuration
To transfer the configuration file to your workstation, follow the procedure
below:
1. Launch the FTP client on your workstation.
2. Type "open" and the IP address of your router. Then type "root" and
SMT password as requested.
3. Locate the 'rom-0' file.
4. Type 'get rom-0' to back up the current router configuration to
your workstation.
For details on FTP commands, please consult the documentation of your FTP
client program. For details on backup using TFTP (note that you must remain
in this menu to back up using TFTP), please see your router manual.


Figure 9-2 Menu 24.5 – System Maintenance – Backup Configuration (Telnet)


9.3 Restore Configuration
Menu 24.6 -– System Maintenance – Restore Configuration allows you to restore the configuration via
the console port.
FTP and TFTP are the preferred methods for restoring your current workstation configuration to your
Prestige since FTP and TFTP are faster. Please note that the system reboots automatically after the file
transfer is complete. The following screen is what you see in Menu 24.5 when connected to the Prestige via
console port.



Ready to restore Configuration via Xmodem.
Do you want to continue (y/n):


Figure 9-3 Menu 24.6 – System Maintenance – Restore Configuration (Console Port)
The following screen is what you see in Menu 24.5 when you telnet into the Prestige.


Menu 24.6 -- System Maintenance - Restore Configuration
To transfer the firmware and configuration file, follow the procedure
below:
1. Launch the FTP client on your workstation.
2. Type "open" and the IP address of your router. Then type "root" and
SMT password as requested.
3. Type "put backupfilename rom-0" where backupfilename is the name of
your backup configuration file on your workstation and rom-spt is the
remote file name on the router. This restores the configuration to
your router.
4. The system reboots automatically after a successful file transfer.
For details on FTP commands, please consult the documentation of your FTP
client program. For details on backup using TFTP (note that you must remain
in this menu to back up using TFTP), please see your router manual.
Press ENTER to Exit:



Figure 9-4 Menu 24.6 – System Maintenance – Restore Configuration (Telnet)


9.4 Upload Firmware
Menu 24.7 -– System Maintenance – Upload Firmware allows you to upgrade the firmware and the
configuration file via the console port. There are two components in the system: the router firmware and the
configuration file, as shown below.


Menu 24.7 -- System Maintenance - Upload Firmware
1. Upload Router Firmware
2. Upload Router Configuration File
Enter Menu Selection Number:


Figure 9-5 Menu 24.7 – System Maintenance – Upload Firmware


9.4.1 Uploading the Router Firmware
Menu 24.7.1 shows you the instructions for uploading the router firmware. Follow the procedure below to
upload the file:
Step 1.
Enter at the prompt to go into debug mode.
y
Step 2.
Enter after message.
atur Enter Debug Mode
Step 3.
Wait for the message before activating Xmodem upload on your
Starting XMODEM upload
terminal.
Step 4.
After successful firmware upload, enter to restart the Prestige.
atgo


Menu 24.7.1 - System Maintenance - Upload Router Firmware
To upload router firmware:
1. Enter "y" at the prompt below to go into debug mode.
2. Enter "atur" after "Enter Debug Mode" message.
3. Wait for "Starting XMODEM upload" message before activating
Xmodem upload on your terminal.
4. After successful firmware upload, enter "atgo" to restart the
router.
Warning: Proceeding with the upload will erase the current router
firmware.
Do You Wish To Proceed:(Y/N)




Figure 9-6 Menu 24.7.1 – System Maintenance – Upload Router Firmware
The screen for Menu 24.7.1 when you telnet into the Prestige (see Figure 9-8) is the same except for the
following additional message.
“For details on FTP commands, please consult the documentation of your FTP client program. For details on
uploading router firmware using TFTP (note that you must remain on this menu to upload router firmware
using TFTP), please see your router manual.”



9.4.2 Uploading Router Configuration File
The configuration data, system-related data, the error log and the trace log are all stored in the configuration
file. Please be aware that uploading the configuration file replaces everything contained within.
Menu 24.6 replaces the current configuration with your customized configuration you
backed up previously. Menu 24.7.2 shows you the instructions for uploading the Router
Configuration file that replaces the current configuration file with the default
configuration file, i.e., P314.rom. You will lose all configurations that you had before
and the speed of the console port will be reset to the default of 9600 bps with 8 data
bit, no parity and 1 stop bit (8n1). You will need to change your serial communications
software to the default before you can connect to the Prestige again. The password will
be reset to the default of 1234, also.
Follow the procedure below to upload the configuration file:
Step 1.
Enter at the prompt to go into debug mode.
y
Step 2.
Enter after the message.
atlc Enter Debug Mode
Step 3.
Wait for the message before activating Xmodem upload on you
Starting XMODEM upload
terminal.
Step 4.
After successful firmware upload, enter to restart the Prestige.
atgo



Menu 24.7.2 - System Maintenance - Upload Router Configuration File
To upload router configuration file:
1. Enter "y" at the prompt below to go into debug mode.
2. Enter "atlc" after "Enter Debug Mode" message.
3. Wait for "Starting XMODEM upload" message before activating
Xmodem upload on your terminal.
4. After successful firmware upload, enter "atgo" to restart the
router.
Warning:
1. Proceeding with the upload will erase the current
configuration file.
2. The router's console port speed (Menu 24.2.2) may change
when it is restarted; please adjust your terminal's speed
accordingly. The password may change (Menu 23), also.
3. When uploading the DEFAULT configuration file, the console
port speed will be reset to 9600 bps and the password to
"1234".
Do You Wish To Proceed:(Y/N)





igure 9-7 Menu 24.7.2 – System Maintenance – Upload Router Configuration File
The screen for Menu 24.7.2 when you telnet into the Prestige (see Figure 9-9) is the same except for the
following additional message.
“For details on FTP commands, please consult the documentation of your FTP client program. For details on
uploading router firmware using TFTP (note that you must remain on this menu to upload router firmware
using TFTP), please see your router manual.”



9.5 TFTP File Transfer
In addition to the direct console port connection, the Prestige supports the up/downloading of the firmware
and the configuration file using TFTP (Trivial File Transfer Protocol) over LAN. Although TFTP should
work over WAN as well, it is not recommended.
To use TFTP, your workstation must have both telnet and TFTP clients. To transfer the firmware and the
configuration file, follow the next procedure:
Step 1.
Use telnet from your workstation to connect to the Prestige and log in. Because TFTP does not
have any security checks, the Prestige records the IP address of the telnet client and accepts TFTP
requests only from this address.
Step 2.
Put the SMT in command interpreter (CI) mode by entering 8 in Menu 24 – System
Maintenance.
Step 3.
Enter command to disable the SMT timeout, so the TFTP transfer will not be
sys stdio 0
interrupted. Enter command to restore the five-minute SMT timeout (default)
sys stdio 5
when the file transfer is complete.
Step 4.
Launch the TFTP client on your workstation and connect to the Prestige. Set the transfer mode to
binary before starting data transfer.
Step 5.
Use the TFTP client (see the example below) to transfer files between the Prestige and the
workstation. The file name for the firmware is and for the configuration file, is (rom-
ras rom-0
zero, not capital o).



Note: If you upload the firmware to the Prestige, it will reboot automatically when the
file transfer is completed (the SYS LED will flash).



Note that the telnet connection must be active and the SMT in CI mode before and during the TFTP transfer.
For details on TFTP commands (see following example), please consult the documentation of your TFTP
client program. For UNIX, use “get” to transfer from the Prestige to the workstation, “put” the other way
around, and “binary” to set binary transfer mode.


真的很多,其實還未完的:|||:

jaork
2007-07-28, 12:40 AM
我諗現在是不是需要買過另一台的ip分享器呢??究竟現在有沒有辦法拯救這台老舊的東東呢??而新式的分享器和舊式的有什麼的分別呢??如果是買的話那買什麼的型號會好一些呢??我有打算架一個ftp出來的...還有家內的電腦以超過七台了..因此,我也想架出一個完美的管理架構來,望能做到長遠的發展,因為我對這方法的東西不太懂,懇請大大給點見議好嗎??XD

mmpo
2007-07-28, 07:47 PM
其實新的IP分享器,大多都有做RESET的按鈕,這當然不是換新的重點

家中的電腦有無線上線的需求,倒是可以趁此機會,換台無線的IP分享器
若有需要QOS的功能,那買台有QOS功能的路由器也不錯
或是拿家裡其中一台不要用的舊電腦裝BrazilFW當路由器也是不錯的選擇

最重要的是好好的看一下TCP/IP的書,你會更了解你自己的需求在那裡




        


本網站是以即時上傳留言的方式運作,一切留言內容只代表發言者個人意見,非本網站之立場,本網站對所有留言的真實性、完整性及立場等,不負任何法律責任。若您發現有某篇留言可能有問題,請 E-Mail 至:www@pczone.com.tw 聯絡我們處理。