--------------------------------------------------------------------------------

The Prestige supports traces when there is problem to connect your ISP using PPPoE protocol. Please follow the procedure below to collect the trace for our troubleshooting.

Remove the LAN cable attached on the Prestige
Enter SMT using console port
Enter Menu 24.8-CI command mode
Type the following commands:
sys trcp sw on (turn on packet trace)
sys errctl 3 (save crash information and make system enter debug mode after the crash)
poe debug 1 (turn on pppoe debug)
dev dial 1 (dial remote node 1)
After all, if the Prestige crashes and you can do nothing, please send the above log back to us.
If the Prestige crashes and you are able to enter commands, please type 'atds' in debug mode to dump the log and send the log to us.
If the Prestige does not crash but just can not dial out, please capture the following further log and send us the log.
sys trcp sw off (turn off packet trace)
sys log disp i (capture system error log)
sys trcp parse (parse the trace in detail)



--------------------------------------------------------------------------------

Example- A trace with system crashes

ras> sys trcp sw on
ras> sys errctl 3
ras> poe debug 1
ras> dev dial 1
Start dialing for node <GPMI>...
poeNetCmdExe: chann poe0 event x420
poeChannDial: start session, peer<GPMI>
bdcastInit: pch poe0
poePut1SrvcName: '' len 0
host-uniq 31303030 len 4
putPoeHdr: ver 1 type 1 code x09 sess-id 0 len 12(x000C)
bdcastSendInit: l1.pktTx() failed, pch poe0 ch enet0
poePut1SrvcName: '' len 0
host-uniq 31303030 len 4
putPoeHdr: ver 1 type 1 code x09 sess-id 0 len 12(x000C)
### Hit any key to continue.###
$$$ DIALING dev=6 ch=0..........
poeI/C: ver 1 type 1 code x07 sessId x0000 len 274(x0112)
poeCtrlI/C: pkt len 274
poeGetTags()
service-name
service-name telstra
service-name bpa
service-name iprimus
service-name pacificinternet
service-name integrationisp
service-name bpa-dev
service-name bpa-sif
service-name telstrarna
service-name gpmsystems
service-name cmux
service-name launceston-broadband
service-name vivanet
service-name n1234567k00
service-name bigpond
service-name n7061992k
service-name n3068223k
service-name n2155202k
service-name n7061995k
AC-name vet1-exhibition-bsn-1
host-uniq 31303030 len 4
PADO recv'd, chann enet1
procPADO: for poe chann poe0
Chann poe0 sending request
poePut1SrvcName: '' len 0
host-uniq 31303030 len 4
putPoeHdr: ver 1 type 1 code x19 sess-id 0 len 12(x000C)
Undefined Address : 0xE3F045C4
Undefined Data : 0x56FF54FF
r0= 0xE3F045C4 r1= 0x0001FFC0 r2= 0x000000E5 r3= 0x56FF54FF
r4= 0xE3F045C4 r5= 0xE5BDBFEC r6= 0x0001C468 r7= 0x60000093
r8= 0x00000000 r9= 0xE3550000 r10=0xE3550000 fp= 0x00000000
r12=0x56FF54FF sp= 0x0001EDBC lr= 0x00004F64 pc= 0x00013954
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
e5bdbfe0: e2 8f 00 06 e5 d5 20 06 e5 d5 20 0a e5 d5 20 0e ...b...f...j...n
e5bdbff0: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc000: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc010: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc020: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc030: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc040: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc050: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc060: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc070: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc080: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc090: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc0a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc0b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc0c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc0d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
e5bdc0e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ed 2b ...b...f...j...n
Bootbase Version: V1.12 | 1/27/2000 11:00:09
RAM: Size = 4096 Kbytes
FLASH: Intel 8M
RAS Version: V3.20(M.01)b2 | 8/18/2000 14:05:08

Enter Debug Mode
atgo
Bootbase Version: V1.12 | 1/27/2000 11:00:09
RAM: Size = 4096 Kbytes
FLASH: Intel 8M
RAS Version: V3.20(M.01)b2 | 8/18/2000 14:05:08

Press any key to enter debug mode within 3 seconds.
............................................................

initialize ch =0, ethernet address: 00:a0:c5:e1:ee:d8
initialize ch =1, ethernet address: 00:a0:c5:e1:ee:d9
Press ENTER to continue...

Enter Password : XXXX

贊助商連結

ㄜ.....
哪位大哥英文好的
可以翻譯一下???

依我很破的英文看下來的結果是

如果你使用 PPPoE 連線到ISP 發生問題, 642R 可以追蹤.
跟著下面的程序自己做故障排除.

先將 642R 的 LAN 拔掉,然後裝上 9Pin 的線到 Console Port.
進到 24.8 CI-Command mode 這個選項
跟著敲以下命令
sys trcp sw on
sys errctl 3
poe debug 1
dev dial 1
之後的狀況如果是掛了, 你什麼也不用做, 把操作過程的 Log 就是用終端機
進到 24.8 後 輸入 和 顯示 的所有訊息 交給他們

如果掛了, 你可以在 Debug mode 輸入命令,
打 atds 把 Log dump 出來 交給他們

如果沒有掛, 只是播不出去, 從以下開始敲的指令訊息 Log 剪下 交給他們
sys trcp sw off
sys log disp i
sys trcp parse