小弟看過精華區的文章,已將Menu15-SUA Server Setup設成
1. Default 192.168.1.100
但是連線過來卻沒連到192.168.1.100而是連到ATU-R上
變成進入ATU-R的選單設定:eek:
是有那裡的設定沒調好嗎???
請大家幫小弟解惑Thanks~~~~~:)
p.s.目前已有開啟硬體撥接及NAT

贊助商連結

能幫小弟一下嗎???
小弟已翻遍精華區還是找不到解答:(
thanks~

Filter 的設定有問題.

最初由 bx2aa 發表
Filter 的設定有問題.
小弟目前的Filter的設定如下
Menu 21.1.1 - TCP/IP Filter Rule

Filter #: 1,1
Filter Type= TCP/IP Filter Rule
Active= No
IP Protocol= 0 IP Source Route= Yes
Destination: IP Addr= 0.0.0.0
IP Mask= 0.0.0.0
Port #=
Port # Comp= None
Source: IP Addr= 0.0.0.0
IP Mask= 0.0.0.0
Port #=
Port # Comp= None
TCP Estab= N/A
More= No Log= None
Action Matched= Check Next Rule
Action Not Matched= Check Next Rule

請問是那裡有誤設呢???
Thanks~

最初由 savage0 發表

小弟目前的Filter的設定如下
Menu 21.1.1 - TCP/IP Filter Rule
Active= No

還有沒有其他的?

有動過的設定只有下面這些,其餘沒列出的選單內容設定均為空白
麻煩您了~thanks~
===========================================================
Menu 1 - General Setup

System Name= HiNet
Location= Taipei
Contact Person's Name= savage's set


Route IP= Yes
Route IPX= No
Bridge= No
===========================================================
Menu 3.2 - TCP/IP and DHCP Ethernet Setup

DHCP Setup
DHCP= Server
Client IP Pool Starting Address= 192.168.1.100
Size of Client IP Pool= 20
Primary DNS Server= 168.95.192.1
Secondary DNS Server= 168.95.1.1
Remote DHCP Server= N/A
TCP/IP Setup:
IP Address= 192.168.1.1
IP Subnet Mask= 255.255.255.0
RIP Direction= Both
Version= RIP-2B
Multicast= IGMP-v2
IP Policies=
Edit IP Alias= No
===========================================================
Menu 3.3 - Novell IPX Ethernet Setup

Seed Router= No

Frame Type 802.2= Yes
IPX Network #= N/A

Frame Type 802.3= No
IPX Network #= N/A

Frame Type Ethernet II= No
IPX Network #= N/A

Frame Type SNAP= No
IPX Network #= N/A
===========================================================
Menu 3.4 - Bridge Ethernet Setup

Handle IPX= None
===========================================================
Menu 4 - Internet Access Setup

ISP's Name= Hinet
Encapsulation= PPPoE
Multiplexing= LLC-based
VPI #= 0
VCI #= 33
Service Name= Any
My Login= ********@hinet.net
My Password= ********
Single User Account= Yes
IP Address Assignment= Dynamic
IP Address= N/A
ENET ENCAP Gateway= N/A
===========================================================
Menu 11.1 - Remote Node Profile

Rem Node Name= Hinet
Active= Yes

Encapsulation= PPPoE
Multiplexing= LLC-based
Incoming:
Rem Login=
Rem Password= ********
Outgoing:
My Login= ********@hinet.net
My Password= ********
Authen= CHAP/PAP
Bridge= No
Edit PPP Options= No
Rem IP Addr= 0.0.0.0
Edit IP/IPX/Bridge= No
Session Options:
Edit Filter Sets= No
PPPoE Idle Timeout(sec)= 0
PPPoE Service Name= Any
Schedule Sets= 1, 1, 1, 1
===========================================================
Menu 15 - SUA Server Setup

Port # IP Address
------ ---------------
1.Default 192.168.1.100
2. 0 0.0.0.0
3. 0 0.0.0.0
4. 0 0.0.0.0
5. 0 0.0.0.0
6. 0 0.0.0.0
7. 0 0.0.0.0
8. 0 0.0.0.0

是 Filter 還有沒有其他的?

最初由 bx2aa 發表
是 Filter 還有沒有其他的?
沒有耶,只有這一個
還是說Filter需要整個刪掉重建呢?

把
Filter #: 1,1
Active= No 改為 Yes
Source Route= Yes 改為 No
Action Matched= Check Next Rule 改為 Forward
試試?

最初由 bx2aa 發表
把
Filter #: 1,1
Active= No 改為 Yes
Source Route= Yes 改為 No
Action Matched= Check Next Rule 改為 Forward
試試?
照您的方法改過了,但還是一樣連到ATU-R裡
有需要動到"Menu 25 - IP Routing Policy Setup"嗎?
目前設定如下
======================================================
Menu 21.1.1 - TCP/IP Filter Rule

Filter #: 1,1
Filter Type= TCP/IP Filter Rule
Active= Yes
IP Protocol= 0 IP Source Route= No
Destination: IP Addr= 0.0.0.0
IP Mask= 0.0.0.0
Port #=
Port # Comp= None
Source: IP Addr= 0.0.0.0
IP Mask= 0.0.0.0
Port #=
Port # Comp= None
TCP Estab= N/A
More= No Log= None
Action Matched= Forward
Action Not Matched= Check Next Rule
======================================================
Menu 3.1 - General Ethernet Setup

Input Filter Sets:
protocol filters= 1
device filters=
Output Filter Sets:
protocol filters=
device filters=
======================================================
thanks~