可以將 CISIO 29XX 兩個PORT 的頻寬合併嗎? [Site Map]

hsyah

2002-02-02, 07:35 PM

http://www.cisco.com/warp/public/473/29-30b.gif
29.html#e1-configs
Configuring the ISL Trunks Between Switches
There are three ISL trunks in this example. Two are configured on EtherChannels and one is configured on a single physical interface.

Configuring trunking on the Catalyst 2948G-L3 requires adding subinterfaces under the main interface, one subinterface for each VLAN transmitted on the trunk. In this example, the VLAN 1 subinterfaces are bridged together to form a single Layer 2 domain for switch management (using IP subnet 10.1.1.0/24).

The remaining VLANs (VLANs 10, 20, 30, and 100) are terminated at the Catalyst 2948G-L3 routed subinterfaces.

On the Catalyst 2948G-L3:

2948G-L3#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
2948G-L3(config)#interface port-channel 1.1
2948G-L3(config-subif)#encapsulation isl 1
2948G-L3(config-subif)#bridge-group 1
2948G-L3(config-subif)#exit
2948G-L3(config)#interface port-channel 1.100
2948G-L3(config-subif)#encapsulation isl 100
2948G-L3(config-subif)#ip address 10.100.100.1 255.255.255.0
2948G-L3(config-subif)#exit
2948G-L3(config)#interface port-channel 2.1
2948G-L3(config-subif)#encapsulation isl 1
2948G-L3(config-subif)#bridge-group 1
2948G-L3(config-subif)#exit
2948G-L3(config)#interface port-channel 2.10
2948G-L3(config-subif)#encapsulation isl 10
2948G-L3(config-subif)#ip address 10.10.10.1 255.255.255.0
2948G-L3(config-subif)#exit
2948G-L3(config)#interface port-channel 2.20
2948G-L3(config-subif)#encapsulation isl 20
2948G-L3(config-subif)#ip address 10.20.20.1 255.255.255.0
2948G-L3(config-subif)#exit
2948G-L3(config)#interface fast 44
2948G-L3(config-if)#no shutdown
2948G-L3(config-if)#exit
2948G-L3(config)#interface fast 44.1
2948G-L3(config-subif)#encapsulation isl 1
2948G-L3(config-subif)#bridge-group 1
2948G-L3(config-subif)#exit
2948G-L3(config)#interface fast 44.30
2948G-L3(config-subif)#encapsulation isl 30
2948G-L3(config-subif)#ip address 10.30.30.1 255.255.255.0
2948G-L3(config-subif)#^Z
2948G-L3#
Notes:

The encapsulation isl vlan command specifies the encapsulation type (ISL) and the VLAN to receive on the subinterface
Notice that the VLAN 1 subinterfaces are not assigned an IP address but are instead added to bridge-group 1, allowing VLAN 1 to span all switches
You can verify the configuration using the show interface command. For example, use the show interface fast 44.30 to verify the VLAN 30 subinterface configuration:

2948G-L3#show interface fast 44.30
FastEthernet44.30 is up, line protocol is up
Hardware is epif_port, address is 0030.40d6.4032 (bia 0030.40d6.4032)
Internet address is 10.30.30.1/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255
Encapsulation ISL Virtual LAN, Color 30.
ARP type: ARPA, ARP Timeout 04:00:00
2948G-L3#
On the Catalyst 3512XL:

3512XL#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
3512XL(config)#interface gig 0/1
3512XL(config-if)#switchport mode trunk
3512XL(config-if)#^Z
3512XL#
Notes:

Notice that the configuration is applied to a single interface in the channel group -- any configuration applied to one interface in the port group is applied to the other interface(s) in the group automatically, and appears in the configuration for each interface
The switchport mode trunk command configures the interface as a trunk port
The 2900XL and 3500XL switches use ISL encapsulation by default when you enable trunking, so there is no need to specify the encapsulation in this case
You can verify the configuration using the show interface switchport command:

3512XL#show interface gig 0/1 switchport
Name: Gi0/1
Switchport: Enabled
Administrative mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: isl
Operational Trunking Encapsulation: isl
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1,100
Pruning VLANs Enabled: NONE

Priority for untagged frames: 0
3512XL#
On the Catalyst 3548XL:

3548XL#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
3548XL(config)#interface fast 0/48
3548XL(config-if)#switchport mode trunk
3548XL(config-if)#^Z
3548XL#
You can verify the configuration using the show interface switchport command.

On the Catalyst 2924XL:

2924XL#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
2924XL(config)#interface fast 0/24
2924XL(config-if)#switchport mode trunk
2924XL(config-if)#^Z
2924XL#
You can verify the configuration using the show interface switchport command.

Configuring End-Station Ports
Now, ports on the Catalyst 3512XL, 3548XL, and 2924XL switches are assigned to VLANs and spanning-tree portfast is enabled.

On the Catalyst 3512XL:

3512XL#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
3512XL(config)#interface fast 0/1
3512XL(config-if)#switchport access vlan 100
3512XL(config-if)#spanning-tree portfast
3512XL(config-if)#exit
3512XL(config)#interface fast 0/2
3512XL(config-if)#switchport access vlan 100
3512XL(config-if)#spanning-tree portfast

. . .

3512XL(config)#interface fast 0/12
3512XL(config-if)#switchport access vlan 100
3512XL(config-if)#spanning-tree portfast
3512XL(config-if)#^Z
3512XL#
You can verify the configuration using the show interface switchport command and the show spanning-tree interface command:

3512XL#show interface fast 0/1 switchport
Name: Fa0/1
Switchport: Enabled
Administrative mode: static access
Operational Mode: static access
Administrative Trunking Encapsulation: isl
Operational Trunking Encapsulation: isl
Negotiation of Trunking: Disabled
Access Mode VLAN: 100 (Server-Farm)
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: NONE
Pruning VLANs Enabled: NONE

Priority for untagged frames: 0
3512XL#show spanning-tree interface fast 0/1
Interface Fa0/1 (port 13) in Spanning tree 100 is FORWARDING
Port path cost 100, Port priority 128
Designated root has priority 32768, address 00d0.5868.eb81
Designated bridge has priority 32768, address 00d0.5868.eb81
Designated port is 13, path cost 0
Timers: message age 0, forward delay 0, hold 0
BPDU: sent 0, received 0
The port is in the portfast mode
3512XL#
On the Catalyst 3548XL:

3548XL#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
3548XL(config)#interface fast 0/1
3548XL(config-if)#switchport access vlan 10
3548XL(config-if)#spanning-tree portfast

. . .

3548XL(config)#interface fast 0/24
3548XL(config-if)#switchport access vlan 10
3548XL(config-if)#spanning-tree portfast
3548XL(config-if)#exit
3548XL(config)#interface fast 0/25
3548XL(config-if)#switchport access vlan 20
3548XL(config-if)#spanning-tree portfast

. . .

3548XL(config)#interface fast 0/44
3548XL(config-if)#switchport access vlan 20
3548XL(config-if)#spanning-tree portfast
3548XL(config-if)#^Z
3548XL#
You can verify the configuration using the show interface switchport command and the show spanning-tree interface command.

On the Catalyst 2924XL:

2924XL#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
2924XL(config)#interface fast 0/1
2924XL(config-if)#switchport access vlan 30
2924XL(config-if)#spanning-tree portfast

. . .

2924XL(config)#interface fast 0/23
2924XL(config-if)#switchport access vlan 30
2924XL(config-if)#spanning-tree portfast
3548XL(config-if)#^Z
3548XL#
You can verify the configuration using the show interface switchport command and the show spanning-tree interface command.