請問cisco 677計時制設定的方式?



贊助商連結


danity2000
2001-12-22, 01:07 PM
小弟買了一台Cisco 677,想把家中的TECOM 1086-B換下來,之前
參考了一些發表過的文章,但是就是無法用軟體撥接的方式,
撥接出去,可以麻煩請用的是計時制而且是用CISCO 677人,
能發表一下內部的設定內容:以下是我的設定內容,使用的是seednet計時制
Cisco Broadband Operating System
CBOS (tm) 677 Software (C677-I-M), Version v2.4.3b - Release Software
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Oct 17 2001 13:23:25
DMT FULL firmware version 0x3019be70
NVRAM image at 0x102f12e0

User Access Verification
Password:*****
cbos>enable
Password:*****

cbos#set nvram erase
cbos#set interface wan0 maxvcs 2
cbos#set password encrypt disable
cbos#set bridging rfc1483 enabled
cbos#set bridging management enabled
cbos#set int wan0 down
cbos#set int wan0 pay disable
cbos#set int wan0-0 close
cbos#set int wan0-0 vpi 0
cbos#set int wan0-0 vci 34
cbos#set int wan0-0 open
cbos#set int wan0 up
cbos#write
cbos#reboot

之後進入cisco 677下show int wan0可以看到

cbos#show int wan0
wan0 ADSL Physical Port
Line Trained
Data rate 512 Kbps down; 64 Kbps up
Line capacity 8832 Kbps down; 832 Kbps up
SNR Margin 39 dB; previous 39 dB
Attenuation 27.0 dB; previous 27.0 dB
Status:
Last Self-Test Result: Not Available
Modem Microcode: 0x3019be70
Configured:
Operational Standard: T1.413
Trellis Coding: Enabled
Echo Cancellation: Disabled
FDQ Adaptation: Enabled
Rate Adaptation: Normal
Overhead Framing: Mode-3
Bit-Swapping: Disabled
ATM Payload Scrambling: Disabled
PGA-Cutback: 2 dB
Actual:
FEC Redundancy Bytes:
Interl. Path: downstream: 16, upstream 16
Fast Path: downstream: 0, upstream 0
Fast Path: downstream: 0, upstream 0
Trellis Coding: Not-Used
Echo Cancellation: Not-Used
FDQ Adaptation: Not-Used
Overhead Framing: Mode-3
Bit-Swapping: Not-Used
Last Line Fault: Init - CRCRA1_ERROR
ATM Statistics:
Interleaved-Path Counters:
HEC errors: 0
LOCD events: 0
Fast-Path Counters:
HEC errors: 0
LOCD events: 0
DSL Statistics:
Superframes: 142
Corrected Superframes: 0
Uncorrected Superframes: 0
LOCD Retrains: 0
LOS Retrains: 0
LOF/RFI Retrains: 0
ES Events: 0
Time Trained (h:m:s) 0:00:02
cbos#show nvram
Warning: traffic may pause while NVRAM is being accessed
[[ CBOS = Section Start ]]
NSOS Maximum Number of VCs = 2
NSOS Encrypt Passwords = disabled
[[ Spanning Tree = Section Start ]]
MAC Bridge = enabled, rfc1483
MAC Bridge Management = enabled
[[ ATM WAN Device Driver = Section Start ]]
ATM WAN Cell Scrambling = disabled
ATM WAN Virtual Connection Parms = 00, 0, 34, 0
但是就是無法用pppoe軟體撥接出去..............:(

贊助商連結


kevinsu
2001-12-23, 01:47 AM
試試看
cbos#set int wan0 trellis-coding disable
cbos#set int wan0 retrain
如果還是不行就試試不要用T1.413用g.dmt跟g.lite
cbos#set int wan0 standard g.dmt

danity2000
2002-01-05, 04:32 PM
經過小弟無意間進到公司裡的小白龜,看到了vci是設定為33,就順便再試了一次
,可以正常使用了,謝謝這裡的朋友提供的意見。