TECOM AR4031B、Wagaly Talk 連接線之組成 By hungwen@PCZONE
(轉貼本文請註明作者、出處)
本連接線使用哈電族 PC2500 內附之 USB 傳輸線 (型號:HL-30), 再加上一個
自行製作之轉接線而成, 如此可以減少自行焊接 Transceiver 接頭之不便.
與 AR4031B 連接請插入 AR4031B 左側之 4Pin 接頭, 與 Wagaly Talk 連接
請插入 Wagaly Talk 電路板上連接針腳之 Pin 2~Pin 5, 連線速率請設為
115200,N,8,1 (連線軟體可以使用 Windows 內建之超級終端機), 以下是
連接線接頭圖片與使用連接線擷取下來的 AR4031B、Wagaly Talk 之開機
訊息 (避免佔用太多版面, 只放上部份內容).
TECOM AR4031B 之開機訊息:
CFE version 1.0.37-5.5 for BCM96345 (32bit,SP,BE)
Build Date: Fri Dec 19 09:54:12 PST 2003 (root@cfe-build-linux)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena.
Initializing Devices.
CPU type 0x28000: 140MHz
Total memory used by CFE: 0x80401000 - 0x80521200 (1180160)
Initialized Data: 0x8041BDC0 - 0x8041D610 (6224)
BSS Area: 0x8041D610 - 0x8041F200 (7152)
Local Heap: 0x8041F200 - 0x8051F200 (1048576)
Stack Area: 0x8051F200 - 0x80521200 (8192)
Text (code) segment: 0x80401000 - 0x8041BDBC (110012)
Boot area (physical): 0x00522000 - 0x00562000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm96345_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : 96345R_EPT
Psi size in KB : 16
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:03:c9:XX:XX:XX
Ethernet PHY Type : External Not Using Reverse MII
Memory size in MB : 8
*** Press any key to stop auto run (1 seconds) ***
Wagaly Talk 之開機訊息:
===========================================================
VoIP Router BRN Loader 1.0 build Aug 26 2003 16:32:39
Broad Net Technology, INC.
===========================================================
read(0)= 24576 read(2)=16410
MX29LV160B bottom boot 16-bit mode found
Copying boot params.....DONE
Press any key to enter command mode ...
[BRN Boot]:
======================
[U] Upload to Flash
[E] Erase Flash
[G] Run Runtime Code
[A] Set MAC Address
[#] Set Serial Number
[V] Set Board Version
[S] Serial Test
[I] Parallel Test
[P] Print Boot Params
======================
[BRN Boot]:g
Unzipping program from bank 3...done
Try to find image for running...
Unzipping program from bank 4...doneABCDEFGHIJDRAM
STCK
MAIN
[GPIO FLOW] SetGpio() Begin ..
[GPIO FLOW] SetGpio() End.
##### _ftext = 0x80001000
##### _fdata = 0x804D0BE0
##### __bss_start = 0x8055CF98
##### end = 0x80E12610
##### Backup len = 574392
##### Backup Data from 0x804D0BE0 to 0x80E42610-0x80ECE9C8
install_exception
sys_irq_init
memlib_init
hw5120cfg_init
InitTimer
InitCommSys: RESOURCE_BASE = 21, NUMRES = 128
InitCommSys: EVENT_BASE = 79, NUMEVT = 256
System startup...
soho initialize COLOR1 : 500000
soho initialize COLOR2 : 800000
manu_id=6000 chip_id=401A
MX29LV160B bottom boot 16-bit mode found
Boot Parameters found !!!
HW_options : 33 4f 0 31
Bootcode version: 1.0
Serial number: 41300XXXX
Hardware version: 1.0
Firmware version: 2.17b (Oct 7 2004 18:08:13)
sizeof(struct III_Config_t) is 63996
 |
回覆時引用此文章
作者：purk
書籤